DNS lookups never use UTF-8

[exim.git] / doc / doc-txt / experimental-spec.txt

diff --git a/doc/doc-txt/experimental-spec.txt b/doc/doc-txt/experimental-spec.txt
index bdab748414d83954f6200cf179360ad27bc442f2..3dbf13f9da71910a2d9a847480cba19049b958d3 100644 (file)
--- a/doc/doc-txt/experimental-spec.txt
+++ b/doc/doc-txt/experimental-spec.txt
@@ -623,10 +623,10 @@ exim will send these forensic emails.  It's also advised that you
 configure a dmarc_forensic_sender because the default sender address
 construction might be inadequate.
 
-  control = dmarc_forensic_enable
+  control = dmarc_enable_forensic
 
 (AGAIN: You can choose not to send these forensic reports by simply
-not putting the dmarc_forensic_enable control line at any point in
+not putting the dmarc_enable_forensic control line at any point in
 your exim config.  If you don't tell it to send them, it will not
 send them.)
 
@@ -755,7 +755,7 @@ b. Configure, somewhere before the DATA ACL, the control option to
 
   deny    dmarc_status   = reject
           !authenticated = *
-          message        = Message from $domain_used_domain failed sender's DMARC policy, REJECT
+          message        = Message from $dmarc_used_domain failed sender's DMARC policy, REJECT
 
 
 
@@ -1086,6 +1086,39 @@ QUIT
 
 
 
+SOCKS
+------------------------------------------------------------
+Support for proxying outbound SMTP via a Socks 5 proxy
+(RFC 1928) is included if Exim is compiled with
+EXPERIMENTAL_SOCKS defined.
+
+If an smtp transport has a nonempty socks_proxy option
+defined, this is active.  The option is expanded and
+should be a list (colon-separated by default) of
+proxy specifiers.  Each proxy specifier is a list
+(space-separated by default) where the initial element
+is an IP address and any subsequent elements are options.
+
+Options are a string <name>=<value>.
+These options are currently defined:
+- "auth", with possible values "none" and "name".
+  Using "name" selects username/password authentication
+  per RFC 1929. Default is "none".
+- "name" sets the authentication username. Default is empty.
+- "pass" sets the authentication password. Default is empty.
+- "port" sets the tcp port number for the proxy. Default is 1080.
+- "tmo" sets a connection timeout in seconds for this proxy. Default is 5.
+
+Proxies from the list are tried in order until
+one responds.  The timeout for the overall connection
+applies to the set of proxied attempts.
+
+If events are used, the remote IP/port during a
+tcp:connect event will be that of the proxy.
+
+
+
+
 DANE
 ------------------------------------------------------------
 DNS-based Authentication of Named Entities, as applied
@@ -1237,6 +1270,37 @@ in combination with EXPERIMENTAL_EVENT), and a new variable
 $tls_out_tlsa_usage (detailed above).
 
 
+
+SMTPUTF8
+------------------------------------------------------------
+Internationalised mail name handling.
+RFCs 6530, 6533, 5890
+
+Compile with EXPERIMENTAL_INTERNATIONAL and libidn.
+
+Main config option smtputf8_advertise_hosts, default '*',
+a host list.  If this matches the sending host and
+accept_8bitmime is true (the default) then the ESMTP option
+SMTPUTF8 will be advertised.
+
+If the sender specifies the SMTPUTF8 option on a MAIL command
+international handling for the message is enabled and
+the expansion variable $message_smtputf8 will have value TRUE.
+
+The option allow_utf8_domains is set to true for this
+message. All DNS lookups are converted to a-label form
+whatever the setting of allow_utf8_domains.
+
+Log lines and Received-by: header lines will aquire a "utf8"
+prefix on the protocol element, eg. utf8esmtp.
+
+Expansion operators:
+       ${utf8_domain_to_alabel:str}
+       ${utf8_domain_from_alabel:str}
+       ${utf8_localpart_to_alabel:str}
+       ${utf8_localpart_from_alabel:str}
+
+
 --------------------------------------------------------------
 End of file
 --------------------------------------------------------------