From ad26813496addda838a0512075cacd58dca01b30 Mon Sep 17 00:00:00 2001 From: Philip Hazel Date: Mon, 15 Jan 2007 15:58:40 +0000 Subject: [PATCH] Spec update. --- doc/doc-docbook/spec.xfpt | 58 +++++++++++++++++++++++---------------- 1 file changed, 35 insertions(+), 23 deletions(-) diff --git a/doc/doc-docbook/spec.xfpt b/doc/doc-docbook/spec.xfpt index 506dd8da5..5856b3f97 100644 --- a/doc/doc-docbook/spec.xfpt +++ b/doc/doc-docbook/spec.xfpt @@ -1,4 +1,4 @@ -. $Cambridge: exim/doc/doc-docbook/spec.xfpt,v 1.13 2006/12/19 12:28:35 ph10 Exp $ +. $Cambridge: exim/doc/doc-docbook/spec.xfpt,v 1.14 2007/01/15 15:58:40 ph10 Exp $ . . ///////////////////////////////////////////////////////////////////////////// . This is the primary source of the Exim Manual. It is an xfpt document that is @@ -19,7 +19,7 @@ .set ACL "access control lists (ACLs)" .set previousversion "4.63" -.set version "4.64" +.set version "4.66" . ///////////////////////////////////////////////////////////////////////////// @@ -121,17 +121,17 @@ Specification of the Exim Mail Transfer Agent The Exim MTA -11 December 2006 +08 January 2007 PhilipHazel PH University of Cambridge Computing Service
New Museums Site, Pembroke Street, Cambridge CB2 3QH, England
- 4.64 - 11 December 2006 + 4.66 + 08 January 2007 PH -2006University of Cambridge +2007University of Cambridge .literal off @@ -7812,10 +7812,17 @@ Consider what will happen if a name cannot be found. Because of the problems of determining host names from IP addresses, matching against host names is not as common as matching against IP addresses. +.new By default, in order to find a host name, Exim first does a reverse DNS lookup; if no name is found in the DNS, the system function (&[gethostbyaddr()]& or &[getipnodebyaddr()]& if available) is tried. The order in which these lookups -are done can be changed by setting the &%host_lookup_order%& option. +are done can be changed by setting the &%host_lookup_order%& option. For +security, once Exim has found one or more names, it looks up the IP addresses +for these names and compares them with the IP address that it started with. +Only those names whose IP addresses match are accepted. Any other names are +discarded. If no names are left, Exim behaves as if the host name cannot be +found. In the most common case there is only one name and one IP address. +.wen There are some options that control what happens if a host name cannot be found. These are described in section &<>& below. @@ -9523,6 +9530,8 @@ Note that the general negation operator provides for inequality testing. The two strings must take the form of optionally signed decimal integers, optionally followed by one of the letters &"K"& or &"M"& (in either upper or lower case), signifying multiplication by 1024 or 1024*1024, respectively. +&new("As a special case, the numerical value of an empty string is taken as +zero.") .vitem &*crypteq&~{*&<&'string1'&>&*}{*&<&'string2'&>&*}*& .cindex "expansion" "encrypted comparison" @@ -13524,13 +13533,16 @@ which is not affected by this option. .cindex "limit" "message size" .cindex "size of message" "limit" This option limits the maximum size of message that Exim will process. The -value is expanded for each incoming -connection so, for example, it can be made to depend on the IP address of the -remote host for messages arriving via TCP/IP. &*Note*&: This limit cannot be -made to depend on a message's sender or any other properties of an individual -message, because it has to be advertised in the server's response to EHLO. -String expansion failure causes a temporary error. A value of zero means no -limit, but its use is not recommended. See also &%bounce_return_size_limit%&. +value is expanded for each incoming connection so, for example, it can be made +to depend on the IP address of the remote host for messages arriving via +TCP/IP. &new("After expansion, the value must be a sequence of decimal digits, +optionally followed by K or M.") + +&*Note*&: This limit cannot be made to depend on a message's sender or any +other properties of an individual message, because it has to be advertised in +the server's response to EHLO. String expansion failure causes a temporary +error. A value of zero means no limit, but its use is not recommended. See also +&%bounce_return_size_limit%&. Incoming SMTP messages are failed with a 552 error if the limit is exceeded; locally-generated messages either get a stderr message or a delivery @@ -18371,15 +18383,15 @@ to ensure that any additional groups associated with the uid are set up. .cindex "size of message" "limit" .cindex "transport" "message size; limiting" This option controls the size of messages passed through the transport. It is -expanded before use; the result of the expansion must be a sequence of digits, -optionally followed by K or M. -If the expansion fails for any reason, including forced failure, or if the -result is not of the required form, delivery is deferred. -If the value is greater than zero and the size of a message exceeds this -limit, the address is failed. If there is any chance that the resulting bounce -message could be routed to the same transport, you should ensure that -&%return_size_limit%& is less than the transport's &%message_size_limit%&, as -otherwise the bounce message will fail to get delivered. +expanded before use; the result of the expansion must be a sequence of decimal +digits, optionally followed by K or M. If the expansion fails for any reason, +including forced failure, or if the result is not of the required form, +delivery is deferred. If the value is greater than zero and the size of a +message exceeds this limit, the address is failed. If there is any chance that +the resulting bounce message could be routed to the same transport, you should +ensure that &%return_size_limit%& is less than the transport's +&%message_size_limit%&, as otherwise the bounce message will fail to get +delivered. -- 2.25.1