domainlist local_domains = @
domainlist relay_to_domains =
-hostlist relay_from_hosts = 127.0.0.1
+hostlist relay_from_hosts = localhost
+# (We rely upon hostname resolution working for localhost, because the default
+# uncommented configuration needs to work in IPv4-only environments.)
# Most straightforward access control requirements can be obtained by
# appropriate settings of the above options. In more complicated situations,
# to any other host on the Internet. Such a setting commonly refers to a
# complete local network as well as the localhost. For example:
#
-# hostlist relay_from_hosts = 127.0.0.1 : 192.168.0.0/16
+# hostlist relay_from_hosts = <; 127.0.0.1 ; ::1 ; 192.168.0.0/16
#
# The "/16" is a bit mask (CIDR notation), not a number of hosts. Note that you
# have to include 127.0.0.1 if you want to allow processes on your host to send
# SMTP mail by using the loopback address. A number of MUAs use this method of
-# sending mail.
+# sending mail. Often, connections are made to "localhost", which might be ::1
+# on IPv6-enabled hosts. Do not forget CIDR for your IPv6 networks.
# All three of these lists may contain many different kinds of item, including
# wildcarded names, regular expressions, and file lookups. See the reference
host_lookup = *
-# The settings below, which are actually the same as the defaults in the
-# code, cause Exim to make RFC 1413 (ident) callbacks for all incoming SMTP
-# calls. You can limit the hosts to which these calls are made, and/or change
-# the timeout that is used. If you set the timeout to zero, all RFC 1413 calls
-# are disabled. RFC 1413 calls are cheap and can provide useful information
-# for tracing problem messages, but some hosts and firewalls have problems
-# with them. This can result in a timeout instead of an immediate refused
-# connection, leading to delays on starting up SMTP sessions. (The default was
-# reduced from 30s to 5s for release 4.61.)
-
-rfc1413_hosts = *
-rfc1413_query_timeout = 5s
+# The settings below cause Exim to make RFC 1413 (ident) callbacks
+# for all incoming SMTP calls. You can limit the hosts to which these
+# calls are made, and/or change the timeout that is used. If you set
+# the timeout to zero, all RFC 1413 calls are disabled. RFC 1413 calls
+# are cheap and can provide useful information for tracing problem
+# messages, but some hosts and firewalls have problems with them.
+# This can result in a timeout instead of an immediate refused
+# connection, leading to delays on starting up SMTP sessions.
+# (The default was reduced from 30s to 5s for release 4.61. and to
+# disabled for release 4.86)
+#
+#rfc1413_hosts = *
+#rfc1413_query_timeout = 5s
# By default, Exim expects all envelope addresses to be fully qualified, that
# and/or qualify_recipient (see above).
+# Unless you run a high-volume site you probably want more logging
+# detail than the default. Adjust to suit.
+
+log_selector = +smtp_protocol_error +smtp_syntax_error \
+ +tls_certificate_verified
+
+
# If you want Exim to support the "percent hack" for certain domains,
# uncomment the following line and provide a list of domains. The "percent
# hack" is the feature by which mail addressed to x%y@z (where z is one of
# because of some popular, yet buggy, mail composition software.
+# If you wish to be strictly RFC compliant, or if you know you'll be
+# exchanging email with systems that are not 8-bit clean, then you may
+# wish to disable advertising 8BITMIME. Uncomment this option to do so.
+
+# accept_8bitmime = false
+
+
######################################################################
# ACL CONFIGURATION #
# Specifies access control lists for incoming SMTP mail #
domains = ! +local_domains
transport = remote_smtp
ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8
+# if ipv6-enabled then instead use:
+# ignore_target_hosts = <; 0.0.0.0 ; 127.0.0.0/8 ; ::1
no_more
+# This alternative router can be used when you want to send all mail to a
+# server which handles DNS lookups for you; an ISP will typically run such
+# a server for their customers. If you uncomment "smarthost" then you
+# should comment out "dnslookup" above. Setting a real hostname in route_data
+# wouldn't hurt either.
+
+# smarthost:
+# driver = manualroute
+# domains = ! +local_domains
+# transport = remote_smtp
+# route_data = MAIL.HOSTNAME.FOR.CENTRAL.SERVER.EXAMPLE
+# ignore_target_hosts = <; 0.0.0.0 ; 127.0.0.0/8 ; ::1
+# no_more
+
+
# The remaining routers handle addresses in the local domain(s), that is those
# domains that are defined by "domainlist local_domains" above.
# server_set_id = $auth2
# server_prompts = :
# server_condition = Authentication is not yet configured
-# server_advertise_condition = ${if def:tls_cipher }
+# server_advertise_condition = ${if def:tls_in_cipher }
# LOGIN authentication has traditional prompts and responses. There is no
# authorization ID in this mechanism, so unlike PLAIN the username and
# server_set_id = $auth1
# server_prompts = <| Username: | Password:
# server_condition = Authentication is not yet configured
-# server_advertise_condition = ${if def:tls_cipher }
+# server_advertise_condition = ${if def:tls_in_cipher }
######################################################################
projects / exim.git / blobdiff