-$Cambridge: exim/doc/doc-txt/NewStuff,v 1.150 2007/06/19 14:41:31 ph10 Exp $
+$Cambridge: exim/doc/doc-txt/NewStuff,v 1.160 2009/11/14 20:35:55 nm4 Exp $
New Features in Exim
--------------------
test from the snapshots or the CVS before the documentation is updated. Once
the documentation is updated, this file is reduced to a short list.
+Version 4.71
+------------
+
+Version 4.70
+------------
+
+ 1. Native DKIM support without an external library.
+
+ 2. Experimental DCC support via dccifd (contributed by Wolfgang Breyha).
+
+
Version 4.68
------------
message to the standard output, in RFC 2822 format. The option can be used
only by an admin user.
+ 5. There is now a /noupdate option for the ratelimit ACL condition. It
+ computes the rate and checks the limit as normal, but it does not update
+ the saved data. This means that, in relevant ACLs, it is possible to lookup
+ the existence of a specified (or auto-generated) ratelimit key without
+ incrementing the ratelimit counter for that key.
+
+ In order for this to be useful, another ACL entry must set the rate
+ for the same key somewhere (otherwise it will always be zero).
+
+ Example:
+
+ acl_check_connect:
+ # Read the rate; if it doesn't exist or is below the maximum
+ # we update it below
+ deny ratelimit = 100 / 5m / strict / noupdate
+ log_message = RATE: $sender_rate / $sender_rate_period \
+ (max $sender_rate_limit)
+
+ [... some other logic and tests...]
+
+ warn ratelimit = 100 / 5m / strict / per_cmd
+ log_message = RATE UPDATE: $sender_rate / $sender_rate_period \
+ (max $sender_rate_limit)
+ condition = ${if le{$sender_rate}{$sender_rate_limit}}
+
+ accept
+
+ 6. The variable $max_received_linelength contains the number of bytes in the
+ longest line that was received as part of the message, not counting the
+ line termination character(s).
+
+ 7. Host lists can now include +ignore_defer and +include_defer, analagous to
+ +ignore_unknown and +include_unknown. These options should be used with
+ care, probably only in non-critical host lists such as whitelists.
+
+ 8. There's a new option called queue_only_load_latch, which defaults true.
+ If set false when queue_only_load is greater than zero, Exim re-evaluates
+ the load for each incoming message in an SMTP session. Otherwise, once one
+ message is queued, the remainder are also.
+
+ 9. There is a new ACL, specified by acl_smtp_notquit, which is run in most
+ cases when an SMTP session ends without sending QUIT. However, when Exim
+ itself is is bad trouble, such as being unable to write to its log files,
+ this ACL is not run, because it might try to do things (such as write to
+ log files) that make the situation even worse.
+
+ Like the QUIT ACL, this new ACL is provided to make it possible to gather
+ statistics. Whatever it returns (accept or deny) is immaterial. The "delay"
+ modifier is forbidden in this ACL.
+
+ When the NOTQUIT ACL is running, the variable $smtp_notquit_reason is set
+ to a string that indicates the reason for the termination of the SMTP
+ connection. The possible values are:
+
+ acl-drop Another ACL issued a "drop" command
+ bad-commands Too many unknown or non-mail commands
+ command-timeout Timeout while reading SMTP commands
+ connection-lost The SMTP connection has been lost
+ data-timeout Timeout while reading message data
+ local-scan-error The local_scan() function crashed
+ local-scan-timeout The local_scan() function timed out
+ signal-exit SIGTERM or SIGINT
+ synchronization-error SMTP synchronization error
+ tls-failed TLS failed to start
+
+ In most cases when an SMTP connection is closed without having received
+ QUIT, Exim sends an SMTP response message before actually closing the
+ connection. With the exception of acl-drop, the default message can be
+ overridden by the "message" modifier in the NOTQUIT ACL. In the case of a
+ "drop" verb in another ACL, it is the message from the other ACL that is
+ used.
+
+10. For MySQL and PostgreSQL lookups, it is now possible to specify a list of
+ servers with individual queries. This is done by starting the query with
+ "servers=x:y:z;", where each item in the list may take one of two forms:
+
+ (1) If it is just a host name, the appropriate global option (mysql_servers
+ or pgsql_servers) is searched for a host of the same name, and the
+ remaining parameters (database, user, password) are taken from there.
+
+ (2) If it contains any slashes, it is taken as a complete parameter set.
+
+ The list of servers is used in exactly the same was as the global list.
+ Once a connection to a server has happened and a query has been
+ successfully executed, processing of the lookup ceases.
+
+ This feature is intended for use in master/slave situations where updates
+ are occurring, and one wants to update a master rather than a slave. If the
+ masters are in the list for reading, you might have:
+
+ mysql_servers = slave1/db/name/pw:slave2/db/name/pw:master/db/name/pw
+
+ In an updating lookup, you could then write
+
+ ${lookup mysql{servers=master; UPDATE ...}
+
+ If, on the other hand, the master is not to be used for reading lookups:
+
+ pgsql_servers = slave1/db/name/pw:slave2/db/name/pw
+
+ you can still update the master by
+
+ ${lookup pgsql{servers=master/db/name/pw; UPDATE ...}
+
+11. The message_body_newlines option (default FALSE, for backwards
+ compatibility) can be used to control whether newlines are present in
+ $message_body and $message_body_end. If it is FALSE, they are replaced by
+ spaces.
+
Version 4.67
------------
projects / exim.git / blobdiff