-$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.122 2005/04/07 10:54:54 ph10 Exp $
+$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.133 2005/05/04 10:17:28 ph10 Exp $
Change log file for Exim from version 4.21
-------------------------------------------
PH/10 Added a nasty fudge to try to recognize and flatten LDAP passwords in
an address' error message when a string expansion fails (syntax or
- whatever). Otherwise not only does the password appear in the log, it may
- also be put in a bounce message.
+ whatever). Otherwise the password may appear in the log. Following change
+ PH/42 below, there is no longer a chance of it appearing in a bounce
+ message.
PH/11 Installed exipick version 20050225.0 from John Jetmore.
PH/36 The change PH/12 above was broken. Fixed it.
+PH/37 Exim used to check for duplicate addresses in the middle of routing, on
+ the grounds that routing the same address twice would always produce the
+ same answer. This might have been true once, but it is certainly no
+ longer true now. Routing a child address may depend on the previous
+ routing that produced that child. Some complicated redirection strategies
+ went wrong when messages had multiple recipients, and made Exim's
+ behaviour dependent on the order in which the addresses were given.
+
+ I have moved the duplicate checking until after the routing is complete.
+ Exim scans the addresses that are assigned to local and remote
+ transports, and removes any duplicates. This means that more work will be
+ done, as duplicates will always all be routed, but duplicates are
+ presumably rare, so I don't expect this is of any significance.
+
+ For deliveries to pipes, files, and autoreplies, the duplicate checking
+ still happens during the routing process, since they are not going to be
+ routed further.
+
+PH/38 Installed a patch from Ian Freislich, with the agreement of Tom Kistner.
+ It corrects a timeout issue with spamd. This is Ian's comment: "The
+ background is that sometimes spamd either never reads data from a
+ connection it has accepted, or it never writes response data. The exiscan
+ spam.[ch] uses a 3600 second timeout on spamd socket reads, further, it
+ blindly assumes that writes won't block so it may never time out."
+
+PH/39 Allow G after quota size as well as K and M.
+
+PH/40 The value set for $authenticated_id in an authenticator may not contain
+ binary zeroes or newlines because the value is written to log lines and
+ to spool files. There was no check on this. Now the value is run through
+ the string_printing() function so that such characters are converted to
+ printable escape sequences.
+
+PH/41 $message_linecount is a new variable that contains the total number of
+ lines in the message. Compare $body_linecount, which is the count for the
+ body only.
+
+PH/42 Exim no longer gives details of delivery errors for specific addresses in
+ bounce and delay warning messages, except in certain special cases, which
+ are as follows:
+
+ (a) An SMTP error message from a remote host;
+ (b) A message specified in a :fail: redirection;
+ (c) A message specified in a "fail" command in a system filter;
+ (d) A message specified in a FAIL return from the queryprogram router;
+ (e) A message specified by the cannot_route_message router option.
+
+ In these cases only, Exim does include the error details in bounce and
+ warning messages. There are also a few cases where bland messages such
+ as "unrouteable address" or "local delivery error" are given.
+
+PH/43 $value is now also set for the "else" part of a ${run expansion.
+
+PH/44 Applied patch from the Sieve maintainer: "The vacation draft is still
+ being worked on, but at least Exim now implements the latest version to
+ play with."
+
+PH/45 In a pipe transport, although a timeout while waiting for the pipe
+ process to complete was treated as a delivery failure, a timeout while
+ writing the message to the pipe was logged, but erroneously treated as a
+ successful delivery. Such timeouts include transport filter timeouts. For
+ consistency with the overall process timeout, these timeouts are now
+ treated as errors, giving rise to delivery failures by default. However,
+ there is now a new Boolean option for the pipe transport called
+ timeout_defer, which, if set TRUE, converts the failures into defers for
+ both kinds of timeout. A transport filter timeout is now identified in
+ the log output.
+
+PH/46 The "scripts/Configure-config.h" script calls "make" at one point. On
+ systems where "make" and "gmake" are different, calling "gmake" at top
+ level broke things. I've arranged for the value of $(MAKE) to be passed
+ from the Makefile to this script so that it can call the same version of
+ "make".
+
A note about Exim versions 4.44 and 4.50
----------------------------------------
projects / exim.git / blobdiff