-$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.72 2005/01/14 11:06:58 ph10 Exp $
+$Cambridge: exim/doc/doc-txt/ChangeLog,v 1.97 2005/03/22 15:45:35 ph10 Exp $
Change log file for Exim from version 4.21
-------------------------------------------
+Exim version 4.51
+-----------------
+
+TK/01 Added Yahoo DomainKeys support via libdomainkeys. See
+ doc/experimental-spec.txt for details. (http://domainkeys.sf.net)
+
+TK/02 Fix ACL "control" statment not being available in MIME ACL.
+
+TK/03 Fix ACL "regex" condition not being available in MIME ACL.
+
+PH/01 Installed a patch from the Sieve maintainer that allows -bf to be used
+ to test Sieve filters that use "vacation".
+
+PH/02 Installed a slightly modified version of Nikos Mavrogiannopoulos' patch
+ that changes the way the GnuTLS parameters are stored in the cache file.
+ The new format can be generated externally. For backward compatibility,
+ if the data in the cache doesn't make sense, Exim assumes it has read an
+ old-format file, and it generates new data and writes a new file. This
+ means that you can't go back to an older release without removing the
+ file.
+
+PH/03 A redirect router that has both "unseen" and "one_time" set does not
+ work if there are any delivery delays because "one_time" forces the
+ parent to be marked "delivered", so its unseen clone is never tried
+ again. For this reason, Exim now forbids the simultaneous setting of
+ these two options.
+
+PH/04 Change 4.11/85 fixed an obscure bug concerned with addresses that are
+ redirected to themselves ("homonym" addresses). Read the long ChangeLog
+ entry if you want to know the details. The fix, however, neglected to
+ consider the case when local delivery batching is involved. The test for
+ "previously delivered" was not happening when checking to see if an
+ address could be batched with a previous (undelivered) one; under
+ certain circumstances this could lead to multiple deliveries to the same
+ address. A one-line patch to add the appropriate test fixes the bug.
+
+PH/05 Renamed the macro SOCKLEN_T as EXIM_SOCKLEN_T because AIX uses SOCKLEN_T
+ in its include files, and this causes problems building Exim.
+
+PH/06 A number of "verify =" ACL conditions have no options (e.g. verify =
+ header_syntax) but Exim was just ignoring anything given after a slash.
+ In particular, this caused confusion with an attempt to use "verify =
+ reverse_host_lookup/defer_ok". An error is now given when options are
+ supplied for verify items that do not have them. (Maybe reverse_host_
+ lookup should have a defer_ok option, but that's a different point.)
+
+PH/07 Increase the size of the buffer for incoming SMTP commands from 512 (as
+ defined by RFC 821) to 2048, because there were problems with some AUTH
+ commands, and RFC 1869 says the size should be increased for extended
+ SMTP commands that take arguments.
+
+PH/08 Added ${dlfunc dynamically loaded function for expansion (code from Tony
+ Finch).
+
+PH/09 Previously, an attempt to use ${perl when it wasn't compiled gave an
+ "unknown" error; now it says that the functionality isn't in the binary.
+
+PH/10 Added a nasty fudge to try to recognize and flatten LDAP passwords in
+ an address' error message when a string expansion fails (syntax or
+ whatever). Otherwise not only does the password appear in the log, it may
+ also be put in a bounce message.
+
+PH/11 Installed exipick version 20050225.0 from John Jetmore.
+
+PH/12 If the last host in a fallback_hosts list was multihomed, only the first
+ of its addresses was ever tried. (Bugzilla bug #2.)
+
+
A note about Exim versions 4.44 and 4.50
----------------------------------------
keys for these records are domain names, not reversed IP addresses. The
dnsdb PTR lookup now tests whether its key is an IP address. If not, it
leaves it alone. Component reversal etc. now happens only for IP addresses.
+ CAN-2005-0021
56. Improve error message when ldap_search() fails in OpenLDAP or Solaris LDAP.
exim, but did not say which command line option was involved. All I could
find was the use of -be with a bad dnsdb PTR lookup, and in that case it is
running as the user.
+ CAN-2005-0021
61. There was a buffer overflow vulnerability in the SPA authentication code
(which came originally from the Samba project). I have added a test to the
spa_base64_to_bits() function which I hope fixes it.
+ CAN-2005-0022
62. Configuration update for GNU/Hurd and variations. Updated Makefile-GNU and
os.h-GNU, and added configuration files for GNUkFreeBSD and GNUkNetBSD.
error if it is another Exim or anything else that does the synchronization
check. A QUIT command is no longer sent after a timeout.
+73. $host_lookup_deferred has been added, to make it easier to detect DEFERs
+ during host lookups.
+
+74. The defer_ok option of callout verification was not working if it was used
+ when verifying addresses in header lines, that is, for this case:
+
+ verify = header_sender/callout=defer_ok
+
+75. A backgrounded daemon closed stdin/stdout/stderr on entry; this meant that
+ those file descriptors could be used for SMTP connections. If anything
+ wrote to stderr (the example that came up was "warn" in embedded Perl), it
+ could be sent to the SMTP client, causing chaos. The daemon now opens
+ stdin, stdout, and stderr to /dev/null when it puts itself into the
+ background.
+
+76. Arrange for output from Perl's "warn" command to be written to Exim's main
+ log by default. The user can override this with suitable Perl magic.
+
+77. The use of log_message on a "discard" ACL verb, which is supposed to add to
+ the log message when discard triggers, was not working for the DATA ACL or
+ for the non-SMTP ACL.
+
+78. Error message wording change in sieve.c.
+
+79. If smtp_accept_max_per_host was set, the number of connections could be
+ restricted to fewer than expected, because the daemon was trying to set up
+ a new connection before checking whether the processes handling previous
+ connections had finished. The check for completed processes is now done
+ earlier. On busy systems, this bug wouldn't be noticed because something
+ else would have woken the daemon, and it would have reaped the completed
+ process earlier.
+
+80. If a message was submitted locally by a user whose login name contained one
+ or more spaces (ugh!), the spool file that Exim wrote was not re-readable.
+ It caused a spool format error. I have fixed the spool reading code. A
+ related problem was that the "from" clause in the Received: line became
+ illegal because of the space(s). It is now covered by ${quote_local_part.
+
+81. Included the latest eximstats from Steve (adds average sizes to HTML Top
+ tables).
+
+82. Updated OS/Makefile-AIX as per message from Mike Meredith.
+
+83. Patch from Sieve maintainer to fix unterminated string problem in
+ "vacation" handling.
+
+84. Some minor changes to the Linux configuration files to help with other
+ OS variants using glibc.
+
+85. One more patch for Sieve to update vacation handling to latest spec.
+
----------------------------------------------------
See the note above about the 4.44 and 4.50 releases.
17. Added HAVE_SYS_STATVFS_H to the os.h file for Linux, as it has had this
support for a long time. Removed HAVE_SYS_VFS_H.
-18. Updated exipick to current release
+18. Updated exipick to current release from John Jetmore.
19. Allow an empty sender to be matched against a lookup in an address list.
Previously the only cases considered were a regular expression, or an
host was specified on the transport, if the DNS lookup yielded more than
one IP address.
-21. Respect the 75-character limit for "encoded words" when doing RFC 2047
- encoding, and increase the buffer size for ${rfc2047: expansion.
+21. The RFC2047 encoding function was originally intended for short strings
+ such as real names; it was not keeping to the 75-character limit for
+ encoded words that the RFC imposes. It now respects the limit, and
+ generates multiple encoded words if necessary. To be on the safe side, I
+ have increased the buffer size for the ${rfc2047: expansion operator from
+ 1024 to 2048 bytes.
-22. errors_to on a router was being ignored for bounce messages.
+22. Failure to deliver a bounce message always caused it to be frozen, even if
+ there was an errors_to setting on the router. The errors_to setting is now
+ respected.
23. If an IPv6 address is given for -bh or -bhc, it is now converted to the
canonical form (fully expanded) before being placed in
24. Updated eximstats to version 1.33
-25. Expand error message when GnuTLS has problems setting up cert/key files.
+25. Include certificate and key file names in error message when GnuTLS fails
+ to set them up, because the GnuTLS error message doesn't include the name
+ of the failing file when there is a problem reading it.
26. Expand error message when OpenSSL has problems setting up cert/key files.
+ As per change 25.
-27. Reset locale after calling embedded Perl, in case it was changed.
+27. Reset the locale to "C" after calling embedded Perl, in case it was changed
+ (this can affect the format of dates).
-28. When checking for a message's continued existence, exim_tidydb was not
- looking in the split spool subdirectories.
+28. exim_tidydb, when checking for the continued existence of a message for
+ which it has found a message-specific retry record, was not finding
+ messages that were in split spool directories. Consequently, it was
+ deleting retry records that should have stayed in existence.
29. eximstats updated to version 1.35
1.34 - allow eximstats to parse syslog lines as well as mainlog lines
1.35 - bugfix such that pie charts by volume are generated correctly
-30. A forced expansion failure in the SPA authenticator is now treated the
- same as in other authenticators (it moves to the next authenticator).
+30. The SPA authentication driver was not abandoning authentication and moving
+ on to the next authenticator when an expansion was forced to fail,
+ contradicting the general specification for all authenticators. Instead it
+ was generating a temporary error. It now behaves as specified.
-31. Fixed the cipher preference order for GnuTLS client usage.
+31. The default ordering of permitted cipher suites for GnuTLS was pessimal
+ (the order specifies the preference for clients). The order is now AES256,
+ AES128, 3DES, ARCFOUR128.
-31. Fixed Sieve buglet: now it explicitly sets From: when generating
- an autoreply.
+31. Small patch to Sieve code - explicitly set From: when generating an
+ autoreply.
-32. More robust handling of very large SMTP responses.
+32. Exim crashed if a remote delivery caused a very long error message to be
+ recorded - for instance if somebody sent an entire SpamAssassin report back
+ as a large number of 550 error lines. This bug was coincidentally fixed by
+ increasing the size of one of Exim's internal buffers (big_buffer) that
+ happened as part of the Exiscan merge. However, to be on the safe side, I
+ have made the code more robust (and fixed the comments that describe what
+ is going on).
-33. Check dnsdb PTR key for IP address before reversing.
+33. Some experimental protocols are using DNS PTR records for new purposes. The
+ keys for these records are domain names, not reversed IP addresses. The
+ dnsdb PTR lookup now tests whether its key is an IP address. If not, it
+ leaves it alone. Component reversal etc. now happens only for IP addresses.
CAN-2005-0021
-34. Put a check in host_aton() to protect against buffer overrun
+34. The host_aton() function is supposed to be passed a string that is known
+ to be a valid IP address. However, in the case of IPv6 addresses, it was
+ not checking this. This is a hostage to fortune. Exim now panics and dies
+ if the condition is not met. A case was found where this could be provoked
+ from a dnsdb PTR lookup with an IPv6 address that had more than 8
+ components; fortuitously, this particular loophole had already been fixed
+ by change 4.50/55 or 4.44/33 above.
+
+ If there are any other similar loopholes, the new check in host_aton()
+ itself should stop them being exploited. The report I received stated that
+ data on the command line could provoke the exploit when Exim was running as
+ exim, but did not say which command line option was involved. All I could
+ find was the use of -be with a bad dnsdb PTR lookup, and in that case it is
+ running as the user.
CAN-2005-0021
-35. Fix buffer overflow vulnerability in spa_base64_to_bits() function.
+35. There was a buffer overflow vulnerability in the SPA authentication code
+ (which came originally from the Samba project). I have added a test to the
+ spa_base64_to_bits() function which I hope fixes it.
CAN-2005-0022
-36. Need to initialize getloadavg() as root in the daemon when
- deliver_drop_privilege is set, for the benefit of the queue runner.
+36. The daemon start-up calls getloadavg() while still root for those OS that
+ need the first call to be done as root, but it missed one case: when
+ deliver_queue_load_max is set with deliver_drop_privilege. This is
+ necessary for the benefit of the queue runner, because there is no re-exec
+ when deliver_drop_privilege is set.
-37. Data saved for $host_data after a lookup involving a named host list was
- corrupted if there was more than one message in an SMTP session.
+37. Caching of lookup data for "hosts =" ACL conditions, when a named host list
+ was in use, was not putting the data itself into the right store pool;
+ consequently, it could be overwritten for a subsequent message in the same
+ SMTP connection. (Fix 4.40/11 dealt with the non-cache case, but overlooked
+ the caching.)
-38. Fixed a very old bug that sometimes lost the final 221 message after QUIT.
+38. Sometimes the final signoff response after QUIT could fail to get
+ transmitted in the non-TLS case. Testing !tls_active instead of tls_active
+ < 0 before doing a fflush(). This bug looks as though it goes back to the
+ introduction of TLS in release 3.20, but "sometimes" must have been rare
+ because the tests only now provoked it.
Exim version 4.43
projects / exim.git / blobdiff