&`fail`& keyword causes a &'forced expansion failure'& &-- see section
&<<SECTforexpfai>>& for an explanation of what this means.
-The supported DNS record types are A, CNAME, MX, NS, PTR, SPF, SRV, and TXT,
+The supported DNS record types are A, CNAME, MX, NS, PTR, SPF, SRV, TLSA and TXT,
and, when Exim is compiled with IPv6 support, AAAA (and A6 if that is also
configured). If no type is given, TXT is assumed. When the type is PTR,
the data can be an IP address, written as normal; inversion and the addition of
.cindex "expansion" "case forcing"
.cindex "&%uc%& expansion item"
This forces the letters in the string into upper-case.
+
+.vitem &*${utf8clean:*&<&'string'&>&*}*&
+.cindex "correction of invalid utf-8 sequences in strings"
+.cindex "utf-8" "utf-8 sequences"
+.cindex "incorrect utf-8"
+.cindex "expansion" "utf-8 forcing"
+.cindex "&%utf8clean%& expansion item"
+This replaces any invalid utf-8 sequence in the string by the character &`?`&.
.endlist
.cindex "&%bool%& expansion condition"
This condition turns a string holding a true or false representation into
a boolean state. It parses &"true"&, &"false"&, &"yes"& and &"no"&
-(case-insensitively); also positive integer numbers map to true if non-zero,
+(case-insensitively); also integer numbers map to true if non-zero,
false if zero.
An empty string is treated as false.
Leading and trailing whitespace is ignored;
-.option headers_add routers string&!! unset
+.option headers_add routers list&!! unset
.cindex "header lines" "adding"
.cindex "router" "adding header lines"
-This option specifies a string of text that is expanded at routing time, and
-associated with any addresses that are accepted by the router. However, this
+This option specifies a list of text headers, newline-separated,
+that is associated with any addresses that are accepted by the router.
+Each item is separately expanded, at routing time. However, this
option has no effect when an address is just being verified. The way in which
the text is used to add header lines at transport time is described in section
&<<SECTheadersaddrem>>&. New header lines are not actually added until the
&"see"& the added header lines.
The &%headers_add%& option is expanded after &%errors_to%&, but before
-&%headers_remove%& and &%transport%&. If the expanded string is empty, or if
-the expansion is forced to fail, the option has no effect. Other expansion
+&%headers_remove%& and &%transport%&. If an item is empty, or if
+an item expansion is forced to fail, the item has no effect. Other expansion
failures are treated as configuration errors.
Unlike most options, &%headers_add%& can be specified multiple times
-.option headers_remove routers string&!! unset
+.option headers_remove routers list&!! unset
.cindex "header lines" "removing"
.cindex "router" "removing header lines"
-This option specifies a string of text that is expanded at routing time, and
-associated with any addresses that are accepted by the router. However, this
+This option specifies a list of text headers, colon-separated,
+that is associated with any addresses that are accepted by the router.
+Each item is separately expanded, at routing time. However, this
option has no effect when an address is just being verified. The way in which
the text is used to remove header lines at transport time is described in
section &<<SECTheadersaddrem>>&. Header lines are not actually removed until
&"see"& the original header lines.
The &%headers_remove%& option is expanded after &%errors_to%& and
-&%headers_add%&, but before &%transport%&. If the expansion is forced to fail,
-the option has no effect. Other expansion failures are treated as configuration
+&%headers_add%&, but before &%transport%&. If an item expansion is forced to fail,
+the item has no effect. Other expansion failures are treated as configuration
errors.
Unlike most options, &%headers_remove%& can be specified multiple times
&%user%& (see below).
-.option headers_add transports string&!! unset
+.option headers_add transports list&!! unset
.cindex "header lines" "adding in transport"
.cindex "transport" "header lines; adding"
-This option specifies a string of text that is expanded and added to the header
+This option specifies a list of text headers, newline-separated,
+which are (separately) expanded and added to the header
portion of a message as it is transported, as described in section
&<<SECTheadersaddrem>>&. Additional header lines can also be specified by
routers. If the result of the expansion is an empty string, or if the expansion
checked, since this option does not automatically suppress them.
-.option headers_remove transports string&!! unset
+.option headers_remove transports list&!! unset
.cindex "header lines" "removing"
.cindex "transport" "header lines; removing"
-This option specifies a string that is expanded into a list of header names;
+This option specifies a list of header names, colon-separated;
these headers are omitted from the message as it is transported, as described
in section &<<SECTheadersaddrem>>&. Header removal can also be specified by
-routers. If the result of the expansion is an empty string, or if the expansion
+routers.
+Each list item is separately expanded.
+If the result of the expansion is an empty string, or if the expansion
is forced to fail, no action is taken. Other expansion failures are treated as
errors and cause the delivery to be deferred.
Unlike most options, &%headers_remove%& can be specified multiple times
-for a router; all listed headers are added.
+for a router; all listed headers are removed.
in clear.
+.option tls_try_verify_hosts smtp "host list&!! unset
+.cindex "TLS" "server certificate verification"
+.cindex "certificate" "verification of server"
+This option gives a list of hosts for which, on encrypted connections,
+certificate verification will be tried but need not succeed.
+The &%tls_verify_certificates%& option must also be set.
+
+
.option tls_verify_certificates smtp string&!! unset
.cindex "TLS" "server certificate verification"
.cindex "certificate" "verification of server"
&$host_address$& are set to the name and address of the server during the
expansion of this option. See chapter &<<CHAPTLS>>& for details of TLS.
+For back-compatability,
+if neither tls_verify_hosts nor tls_try_verify_hosts are set
+and certificate verification fails the TLS connection is closed.
+
+
+.option tls_verify_hosts smtp "host list&!! unset
+.cindex "TLS" "server certificate verification"
+.cindex "certificate" "verification of server"
+This option gives a list of hosts for which. on encrypted connections,
+certificate verification must succeed.
+The &%tls_verify_certificates%& option must also be set.
+If both this option and &%tls_try_verify_hosts%& are unset
+operation is as if this option selected all hosts.
+
expected server certificates. The client verifies the server's certificate
against this collection, taking into account any revoked certificates that are
in the list defined by &%tls_crl%&.
+Failure to verify fails the TLS connection unless either of the
+&%tls_verify_hosts%& or &%tls_try_verify_hosts%& options are set.
+
+The &%tls_verify_hosts%& and &%tls_try_verify_hosts%& options restrict
+certificate verification to the listed servers. Verification either must
+or need not succeed respectively.
If
&%tls_require_ciphers%& is set on the &(smtp)& transport, it must contain a
requested in the same ACL it is held open and used for the data, otherwise one is made
after the ACL completes.
-Note that routers are used in verify mode. Note also that headers cannot be
+Note that routers are used in verify mode,
+and cannot depend on content of received headers.
+Note also that headers cannot be
modified by any of the post-data ACLs (DATA, MIME and DKIM).
+Headers may be modified by routers (subject to the above) and transports.
+
Cutthrough delivery is not supported via transport-filters or when DKIM signing
of outgoing messages is done, because it sends data to the ultimate destination
before the entire message has been received from the source.
send email. Details of how this works are given in section
&<<SECTverifyCSA>>&.
+.new
+.vitem &*verify&~=&~header_names_ascii*&
+.cindex "&%verify%& ACL condition"
+.cindex "&ACL;" "verifying header names only ASCII"
+.cindex "header lines" "verifying header names only ASCII"
+.cindex "verifying" "header names only ASCII"
+This condition is relevant only in an ACL that is run after a message has been
+received, that is, in an ACL specified by &%acl_smtp_data%& or
+&%acl_not_smtp%&. It checks all header names (not the content) to make sure
+there are no non-ASCII characters, also excluding control characters. The
+allowable characters are decimal ASCII values 33 through 126.
+
+Exim itself will handle headers with non-ASCII characters, but it can cause
+problems for downstream applications, so this option will allow their
+detection and rejection in the DATA ACL's.
+.wen
+
.vitem &*verify&~=&~header_sender/*&<&'options'&>
.cindex "&%verify%& ACL condition"
.cindex "&ACL;" "verifying sender in the header"
dnslists = some.list.example
.endd
+If an explicit key is being used for a DNS lookup and it may be an IPv6
+address you should specify alternate list separators for both the outer
+(DNS list name) list and inner (lookup keys) list:
+.code
+ dnslists = <; dnsbl.example.com/<|$acl_m_addrslist
+.endd
+
.section "Rate limiting incoming messages" "SECTratelimiting"
.cindex "rate limiting" "client sending"
.cindex "limiting client sending rates"
&%hosts%& setting, the transport's hosts are used. If an &(smtp)& transport has
&%hosts_override%& set, its hosts are always used, whether or not the router
supplies a host list.
+Callouts are only supported on &(smtp)& transports.
The port that is used is taken from the transport, if it is specified and is a
remote transport. (For routers that do verification only, no transport need be
.endd
You can safely omit this option (the default value is 1).
+.vitem &%sock%&
+.cindex "virus scanners" "simple socket-connected"
+This is a general-purpose way of talking to simple scanner daemons
+running on the local machine.
+There are four options:
+an address (which may be an IP addres and port, or the path of a Unix socket),
+a commandline to send (may include a single %s which will be replaced with
+the path to the mail file to be scanned),
+an RE to trigger on from the returned data,
+an RE to extract malware_name from the returned data.
+For example:
+.code
+av_scanner = sock:127.0.0.1 6001:%s:(SPAM|VIRUS):(.*)\$
+.endd
+Default for the socket specifier is &_/tmp/malware.sock_&.
+Default for the commandline is &_%s\n_&.
+Both regular-expressions are required.
+
.vitem &%sophie%&
.cindex "virus scanners" "Sophos and Sophie"
Sophie is a daemon that uses Sophos' &%libsavi%& library to scan for viruses.
the transport cannot refer to the modified header lines, because such
expansions all occur before the message is actually transported.
-For both routers and transports, the result of expanding a &%headers_add%&
+For both routers and transports, the argument of a &%headers_add%&
option must be in the form of one or more RFC 2822 header lines, separated by
newlines (coded as &"\n"&). For example:
.code
Exim does not check the syntax of these added header lines.
Multiple &%headers_add%& options for a single router or transport can be
-specified; the values will be concatenated (with a separating newline
-added) before expansion.
+specified; the values will append to a single list of header lines.
+Each header-line is separately expanded.
-The result of expanding &%headers_remove%& must consist of a colon-separated
+The argument of a &%headers_remove%& option must consist of a colon-separated
list of header names. This is confusing, because header names themselves are
often terminated by colons. In this case, the colons are the list separators,
not part of the names. For example:
.endd
Multiple &%headers_remove%& options for a single router or transport can be
-specified; the values will be concatenated (with a separating colon
-added) before expansion.
+specified; the arguments will append to a single header-names list.
+Each item is separately expanded.
-When &%headers_add%& or &%headers_remove%& is specified on a router, its value
-is expanded at routing time, and then associated with all addresses that are
+When &%headers_add%& or &%headers_remove%& is specified on a router,
+items are expanded at routing time,
+and then associated with all addresses that are
accepted by that router, and also with any new addresses that it generates. If
an address passes through several routers as a result of aliasing or
forwarding, the changes are cumulative.
&`R `& on &`<=`& lines: reference for local bounce
&` `& on &`=>`& &`**`& and &`==`& lines: router name
&`S `& size of message
+&`SNI `& server name indication from TLS client hello
&`ST `& shadow transport name
&`T `& on &`<=`& lines: message subject (topic)
&` `& on &`=>`& &`**`& and &`==`& lines: transport name
.next
.cindex "log" "smtp confirmation"
.cindex "SMTP" "logging confirmation"
-&%smtp_confirmation%&: The response to the final &"."& in the SMTP dialogue for
+.cindex "LMTP" "logging confirmation"
+&%smtp_confirmation%&: The response to the final &"."& in the SMTP or LMTP dialogue for
outgoing messages is added to delivery log lines in the form &`C=`&<&'text'&>.
A number of MTAs (including Exim) return an identifying string in this
response.
projects / exim.git / blobdiff