.set I " "
.macro copyyear
-2019
+2020
.endmacro
. /////////////////////////////////////////////////////////////////////////////
contain any forward slash characters.
If &[lstat()]& succeeds then so does the lookup.
.new
+.cindex "tainted data" "dsearch result"
+The result is regarded as untainted.
+
Options for the lookup can be given by appending them after the word "dsearch",
-separated by a comma. Options, if present, are a comma-separated list with
+separated by a comma. Options, if present, are a comma-separated list having
each element starting with a tag name and an equals.
-The only option currently supported requests an alternate output value of
+Two options are supported, for the return value and for filtering match
+candidates.
+The "ret" option requests an alternate result value of
the entire path for the entry. Example:
.code
${lookup {passwd} dsearch,ret=full {/etc}}
.endd
The default result is just the requested entry.
-
-The matching entry may be a file, directory,
-symbolic link, or any other kind of directory entry.
-.cindex "tainted data" "dsearch result"
-The result is regarded as untainted.
+The "filter" option requests that only directory entries of a given type
+are matched. The match value is one of "file", "dir" or "subdir" (the latter
+not matching "." or ".."). Example:
+.code
+${lookup {passwd} dsearch,filter=file {/etc}}
+.endd
+The default matching is for any entry type, including directories
+and symlinks.
.wen
+
An example of how this
lookup can be used to support virtual domains is given in section
&<<SECTvirtualdomains>>&.
escapes whitespace and backslash characters with a backslash.
.section "Specifying the server in the query" "SECTspeserque"
+.new
For MySQL, PostgreSQL and Redis lookups (but not currently for Oracle and InterBase),
it is possible to specify a list of servers with an individual query. This is
-done by starting the query with
+done by appending a comma-separated option to the query type:
.display
-&`servers=`&&'server1:server2:server3:...'&&`;`&
.endd
+&`,servers=`&&'server1:server2:server3:...'&
+.wen
Each item in the list may take one of two forms:
.olist
If it contains no slashes it is assumed to be just a host name. The appropriate
.endd
In an updating lookup, you could then write:
.code
-${lookup mysql{servers=master; UPDATE ...} }
+${lookup mysql,servers=master {UPDATE ...} }
.endd
That query would then be sent only to the master server. If, on the other hand,
the master is not to be used for reading, and so is not present in the global
option, you can still update it by a query of this form:
.code
-${lookup pgsql{servers=master/db/name/pw; UPDATE ...} }
+${lookup pgsql,servers=master/db/name/pw {UPDATE ...} }
.endd
+.new
+An older syntax places the servers speciification before the qury,
+semicolon separated:
+.code
+${lookup mysql{servers=master; UPDATE ...} }
+.endd
+The new version avoids potential issues with tainted
+arguments in the query, for explicit expansion.
+&*Note*&: server specifications in list-style lookups are still problematic.
+.wen
+
.section "Special MySQL features" "SECID73"
For MySQL, an empty host name or the use of &"localhost"& in &%mysql_servers%&
.new
.oindex &%sqlite_dbfile%&
-The preferred way of specifying the file is by using the
+The preferred way of specifying the file is by using the
&%sqlite_dbfile%& option, set to
-.wen
an absolute path.
+.wen
A deprecated method is available, prefixing the query with the filename
separated by white space.
This means that the path name cannot contain white space.
the entire query including the filename - resulting in a refusal to open
the file.
+.new
Here is a lookup expansion example:
.code
sqlite_dbfile = /some/thing/sqlitedb
domainlist relay_to_domains = sqlite;\
select * from relays where ip='$sender_host_address';
.endd
+.wen
The only character affected by the &%quote_sqlite%& operator is a single
quote, which it doubles.
&%domains%& option on a router, the data is preserved in the &$domain_data$&
variable and can be referred to in other options.
.next
+.new
+If the pattern starts with the name of a lookup type
+of either kind (single-key or query-style) it may be
+followed by a command and options,
+The options are lookup-type specific and consist of a comma-separated list.
+Each item starts with a tag and and equals "=".
+.wen
+.next
.cindex "domain list" "matching literal domain name"
If none of the above cases apply, a caseless textual comparison is made
between the pattern and the domain.
.endd
The third argument is a list of options, of which the first element is the timeout
-and must be present if the argument is given.
+and must be present if any options are given.
Further elements are options of form &'name=value'&.
-Two option types is currently recognised: shutdown and tls.
-The first defines whether (the default)
-or not a shutdown is done on the connection after sending the request.
-Example, to not do so (preferred, eg. by some webservers):
+Example:
.code
${readsocket{/socket/name}{request string}{3s:shutdown=no}}
.endd
-The second, tls, controls the use of TLS on the connection. Example:
-.code
-${readsocket{/socket/name}{request string}{3s:tls=yes}}
-.endd
-The default is to not use TLS.
+
+.new
+The following option names are recognised:
+.ilist
+&*cache*&
+Defines if the result data can be cached for use by a later identical
+request in the same process.
+Values are &"yes"& or &"no"& (the default).
+If not, all cached results for this connection specification
+will be invalidated.
+
+.next
+&*shutdown*&
+Defines whether or not a write-shutdown is done on the connection after
+sending the request. Values are &"yes"& (the default) or &"no"&
+(preferred, eg. by some webservers).
+
+.next
+&*tls*&
+Controls the use of TLS on the connection.
+Values are &"yes"& or &"no"& (the default).
If it is enabled, a shutdown as descripbed above is never done.
+.endlist
+.wen
+
A fourth argument allows you to change any newlines that are in the data
that is read, in the same way as for &%readfile%& (see above). This example
dns_dnssec_ok = 1
.endd
+.new
+In addition, on Linux with glibc 2.31 or newer the resolver library will
+default to stripping out a successful validation status.
+This will break a previously working Exim installation.
+Provided that you do trust the resolver (ie, is on localhost) you can tell
+glibc to pass through any successful validation with a new option in
+&_/etc/resolv.conf_&:
+.code
+options trust-ad
+.endd
+.wen
+
Exim does not perform DNSSEC validation itself, instead leaving that to a
validating resolver (e.g. unbound, or bind with suitable configuration).
.table2
.row &%dkim_verify_hashes%& "DKIM hash methods accepted for signatures"
.row &%dkim_verify_keytypes%& "DKIM key types accepted for signatures"
+.row &%dkim_verify_min_keysizes%& "DKIM key sizes accepted for signatures"
.row &%dkim_verify_signers%& "DKIM domains for which DKIM ACL is run"
.row &%host_lookup%& "host name looked up for these hosts"
.row &%host_lookup_order%& "order of DNS and local name lookups"
and an order of processing.
Signatures with algorithms not in the list will be ignored.
+
+.new
+.option dkim_verify_min_keysizes main "string list" "rsa=1024 ed25519=250"
+This option gives a list of key sizes which are acceptable in signatures.
+The list is keyed by the algorithm type for the key; the values are in bits.
+Signatures with keys smaller than given by this option will fail verification.
+
+The default enforces the RFC 8301 minimum key size for RSA signatures.
+.wen
+
.option dkim_verify_minimal main boolean false
If set to true, verification of signatures will terminate after the
first success.
If the resolver library does not support DNSSEC then this option has no effect.
+.new
+On Linux with glibc 2.31 or newer this is insufficient, the resolver library
+will default to stripping out a successful validation status.
+This will break a previously working Exim installation.
+Provided that you do trust the resolver (ie, is on localhost) you can tell
+glibc to pass through any successful validation with a new option in
+&_/etc/resolv.conf_&:
+.code
+options trust-ad
+.endd
+.wen
+
.option dns_ipv4_lookup main "domain list&!!" unset
.cindex "IPv6" "DNS lookup for AAAA records"
${if def:sender_helo_name {(helo=$sender_helo_name)\n\t}}}}\
by $primary_hostname \
${if def:received_protocol {with $received_protocol }}\
- ${if def:tls_ver { ($tls_ver)}}\
+ ${if def:tls_in_ver { ($tls_in_ver)}}\
${if def:tls_in_cipher_std { tls $tls_in_cipher_std\n\t}}\
(Exim $version_number)\n\t\
${if def:sender_address \
${if def:received_for {\n\tfor $received_for}}
.endd
-The reference to the TLS cipher is omitted when Exim is built without TLS
+The references to the TLS version and cipher are
+omitted when Exim is built without TLS
support. The use of conditional expansions ensures that this works for both
locally generated messages and messages received from remote hosts, giving
header lines such as the following:
used. For example:
.code
require_files = mail:/some/file
-require_files = $local_part:$home/.procmailrc
+require_files = $local_part_verified:$home/.procmailrc
.endd
If a user or group name in a &%require_files%& list does not exist, the
&%require_files%& condition fails.
.option dkim_strict smtp string&!! unset
This option defines how Exim behaves when signing a message that
should be signed fails for some reason. When the expansion evaluates to
-either "1" or "true", Exim will defer. Otherwise Exim will send the message
+either &"1"& or &"true"&, Exim will defer. Otherwise Exim will send the message
unsigned. You can use the &%$dkim_domain%& and &%$dkim_selector%& expansion
variables here.
When unspecified, the header names listed in RFC4871 will be used,
whether or not each header is present in the message.
The default list is available for the expansion in the macro
-"_DKIM_SIGN_HEADERS".
+&"_DKIM_SIGN_HEADERS"&
+.new
+and an oversigning variant is in &"_DKIM_OVERSIGN_HEADERS"&.
+.wen
If a name is repeated, multiple headers by that name (or the absence thereof)
will be signed. The textually later headers in the headers part of the
message are signed first, if there are multiples.
-A name can be prefixed with either an '=' or a '+' character.
-If an '=' prefix is used, all headers that are present with this name
+A name can be prefixed with either an &"="& or a &"+"& character.
+If an &"="& prefix is used, all headers that are present with this name
will be signed.
-If a '+' prefix if used, all headers that are present with this name
+If a &"+"& prefix if used, all headers that are present with this name
will be signed, and one signature added for a missing header with the
name will be appended.
.vitem &%$dkim_key_length%&
Number of bits in the key.
+.new
+Valid only once the key is loaded, which is at the time the header signature
+is verified, which is after the body hash is.
+.wen
Note that RFC 8301 says:
.code
less than 1024 bits as valid signatures.
.endd
-To enforce this you must have a DKIM ACL which checks this variable
-and overwrites the &$dkim_verify_status$& variable as discussed above.
-As EC keys are much smaller, the check should only do this for RSA keys.
+This is enforced by the default setting for the &%dkim_verify_min_keysizes%&
+option.
.endlist
projects / exim.git / blobdiff