.cindex "distribution" "https site"
The master distribution site for the Exim distribution is
.display
-.url(https://downloads.exim.org/)
+&url(https://downloads.exim.org/)
.endd
The service is available over HTTPS, HTTP and FTP.
We encourage people to migrate to HTTPS.
described in more detail in chapter &<<CHAProutergeneric>>&.
.ilist
+.cindex affix "router precondition"
The &%local_part_prefix%& and &%local_part_suffix%& options can specify that
the local parts handled by the router may or must have certain prefixes and/or
suffixes. If a mandatory affix (prefix or suffix) is not present, the router is
.vindex "&$local_part_prefix$&"
.vindex "&$local_part$&"
.vindex "&$local_part_suffix$&"
+.cindex affix "router precondition"
If the &%local_parts%& option is set, the local part of the address must be in
the set of local parts that it defines. If &%local_part_prefix%& or
&%local_part_suffix%& is in use, the prefix or suffix is removed from the local
.vitem &%-bfp%&&~<&'prefix'&>
.oindex "&%-bfp%&"
+.cindex affix "filter testing"
This sets the prefix of the local part of the recipient address when a filter
file is being tested by means of the &%-bf%& option. The default is an empty
prefix.
.vitem &%-bfs%&&~<&'suffix'&>
.oindex "&%-bfs%&"
+.cindex affix "filter testing"
This sets the suffix of the local part of the recipient address when a filter
file is being tested by means of the &%-bf%& option. The default is an empty
suffix.
&<<CHAPlocalscan>>&)
&`lookup `& general lookup code and all lookups
&`memory `& memory handling
-&`pid `& add pid to debug output lines
+&`noutf8 `& modifier: avoid UTF-8 line-drawing
+&`pid `& modifier: add pid to debug output lines
&`process_info `& setting info for the process log
&`queue_run `& queue runs
&`receive `& general message reception logic
&`retry `& retry handling
&`rewrite `& address rewriting
&`route `& address routing
-&`timestamp `& add timestamp to debug output lines
+&`timestamp `& modifier: add timestamp to debug output lines
&`tls `& TLS logic
&`transport `& transports
&`uid `& changes of uid/gid and looking up uid/gid
of all debug output lines. This can be useful when trying to track down delays
in processing.
+.new
+.cindex debugging "UTF-8 in"
+.cindex UTF-8 "in debug output"
+The &`noutf8`& selector disables the use of
+UTF-8 line-drawing characters to group related information.
+When disabled. ascii-art is used instead.
+Using the &`+all`& option does not set this modifier,
+.wen
+
If the &%debug_print%& option is set in any driver, it produces output whenever
any debugging is selected, or if &%-v%& is used.
&*Warning*&: Unlike most other single-key lookup types, a file of data for
&((n)wildlsearch)& can &'not'& be turned into a DBM or cdb file, because those
lookup types support only literal keys.
+
+.next
+.cindex "lookup" "spf"
+If Exim is built with SPF support, manual lookups can be done
+(as opposed to the standard ACL condition method.
+For details see section &<<SECSPF>>&.
.endlist ilist
This forces an expansion failure (see section &<<SECTforexpfai>>&);
{<&'string2'&>} must be present for &"fail"& to be recognized.
+.new
+.vitem "&*${extract json{*&<&'key'&>&*}{*&<&'string1'&>&*}{*&<&'string2'&>&*}&&&
+ {*&<&'string3'&>&*}}*&"
+.cindex "expansion" "extracting from JSON object"
+.cindex JSON expansions
+The key and <&'string1'&> are first expanded separately. Leading and trailing
+white space is removed from the key (but not from any of the strings). The key
+must not be empty and must not consist entirely of digits.
+The expanded <&'string1'&> must be of the form:
+.display
+{ <&'"key1"'&> : <&'value1'&> , <&'"key2"'&> , <&'value2'&> ... }
+.endd
+.vindex "&$value$&"
+The braces, commas and colons, and the quoting of the member name are required;
+the spaces are optional.
+Matching of the key against the member names is done case-sensitively.
+. XXX should be a UTF-8 compare
+
+The results of matching are handled as above.
+.wen
+
.vitem "&*${extract{*&<&'number'&>&*}{*&<&'separators'&>&*}&&&
{*&<&'string1'&>&*}{*&<&'string2'&>&*}{*&<&'string3'&>&*}}*&"
empty (for example, the fifth field above).
+.new
+.vitem "&*${extract json{*&<&'number'&>&*}}&&&
+ {*&<&'string1'&>&*}{*&<&'string2'&>&*}{*&<&'string3'&>&*}}*&"
+.cindex "expansion" "extracting from JSON array"
+.cindex JSON expansions
+The <&'number'&> argument must consist entirely of decimal digits,
+apart from leading and trailing white space, which is ignored.
+
+Field selection and result handling is as above;
+there is no choice of field separator.
+.wen
+
+
.vitem &*${filter{*&<&'string'&>&*}{*&<&'condition'&>&*}}*&
.cindex "list" "selecting by condition"
.cindex "expansion" "selecting from list by condition"
.vitem &*$rheader_*&<&'header&~name'&>&*:*&&~or&~&*$rh_*&<&'header&~name'&>&*:*&
This item inserts &"raw"& header lines. It is described with the &%header%&
-expansion item above.
+expansion item in section &<<SECTexpansionitems>>& above.
.vitem "&*${run{*&<&'command'&>&*&~*&<&'args'&>&*}{*&<&'string1'&>&*}&&&
{*&<&'string2'&>&*}}*&"
the value of &$authenticated_id$& is normally the login name of the calling
process. However, a trusted user can override this by means of the &%-oMai%&
command line option.
-This second case also sets up inforamtion used by the
+This second case also sets up information used by the
&$authresults$& expansion item.
.vitem &$authenticated_fail_id$&
inserting the message header line with the given name. Note that the name must
be terminated by colon or white space, because it may contain a wide variety of
characters. Note also that braces must &'not'& be used.
+See the full description in section &<<SECTexpansionitems>>& above.
.vitem &$headers_added$&
.vindex "&$headers_added$&"
.vindex "&$local_part_prefix$&"
.vindex "&$local_part_suffix$&"
+.cindex affix variables
If a local part prefix or suffix has been recognized, it is not included in the
value of &$local_part$& during routing and subsequent delivery. The values of
any prefix or suffix are in &$local_part_prefix$& and
.vitem &$local_part_prefix$&
.vindex "&$local_part_prefix$&"
+.cindex affix variables
When an address is being routed or delivered, and a
specific prefix for the local part was recognized, it is available in this
variable, having been removed from &$local_part$&.
.option local_part_prefix routers&!? "string list" unset
+.cindex affix "router precondition"
.cindex "router" "prefix for local part"
.cindex "prefix" "for local part, used in router"
If this option is set, the router is skipped unless the local part starts with
A list of hosts, whether obtained via &%route_data%& or &%route_list%&, is
always separately expanded before use. If the expansion fails, the router
declines. The result of the expansion must be a colon-separated list of names
-and/or IP addresses, optionally also including ports. The format of each item
+and/or IP addresses, optionally also including ports.
+If the list is written with spaces, it must be protected with quotes.
+The format of each item
in the list is described in the next section. The list separator can be changed
as described in section &<<SECTlistconstruct>>&.
.option delay_after_cutoff smtp boolean true
+.cindex "final cutoff" "retries, controlling"
+.cindex retry "final cutoff"
This option controls what happens when all remote IP addresses for a given
domain have been inaccessible for so long that they have passed their retry
cutoff times.
If the value of this option begins with a digit it is taken as a port number;
otherwise it is looked up using &[getservbyname()]&. The default value is
-normally &"smtp"&, but if &%protocol%& is set to &"lmtp"&, the default is
-&"lmtp"&. If the expansion fails, or if a port number cannot be found, delivery
+normally &"smtp"&,
+but if &%protocol%& is set to &"lmtp"& the default is &"lmtp"&
+and if &%protocol%& is set to &"smtps"& the default is &"smtps"&.
+If the expansion fails, or if a port number cannot be found, delivery
is deferred.
+.new
+Note that at least one Linux distribution has been seen failing
+to put &"smtps"& in its &"/etc/services"& file, resulting is such deferrals.
+.wen
+
.option protocol smtp string smtp
If this option is set to &"smtps"&, the default value for the &%port%& option
changes to &"smtps"&, and the transport initiates TLS immediately after
connecting, as an outbound SSL-on-connect, instead of using STARTTLS to upgrade.
-The Internet standards bodies strongly discourage use of this mode.
+.new
+The Internet standards bodies used to strongly discourage use of this mode,
+but as of RFC 8314 it is perferred over STARTTLS for message submission
+(as distinct from MTA-MTA communication).
+.wen
.option retry_include_ip_address smtp boolean&!! true
messages. If this delivery fails, the address fails immediately. The
post-cutoff retry time is not used.
+.cindex "final cutoff" "retries, controlling"
+.cindex retry "final cutoff"
If the delivery is remote, there are two possibilities, controlled by the
.oindex "&%delay_after_cutoff%&"
&%delay_after_cutoff%& option of the &(smtp)& transport. The option is true by
-default. Until the post-cutoff retry time for one of the IP addresses is
+default. Until the post-cutoff retry time for one of the IP addresses,
+as set by the &%retry_data_expire%& option, is
reached, the failing email address is bounced immediately, without a delivery
attempt taking place. After that time, one new delivery attempt is made to
those IP addresses that are past their retry times, and if that still fails,
.option server_set_id authenticators string&!! unset
.vindex "&$authenticated_id$&"
+.vindex "&$authenticated_fail_id$&"
When an Exim server successfully authenticates a client, this string is
expanded using data from the authentication, and preserved for any incoming
messages in the variable &$authenticated_id$&. It is also included in the log
lines for incoming messages. For example, a user/password authenticator
configuration might preserve the user name that was used to authenticate, and
refer to it subsequently during delivery of the message.
+On a failing authentication the expansion result is instead saved in
+the &$authenticated_fail_id$& variable.
If expansion fails, the option is ignored.
apply to all TLS connections. For any host that matches one of these options,
Exim requests a certificate as part of the setup of the TLS session. The
contents of the certificate are verified by comparing it with a list of
-expected certificates.
+expected trust-anchors or certificates.
These may be the system default set (depending on library version),
an explicit file or,
depending on library version, a directory, identified by
.endd
where &_/cert/file_& contains a single certificate.
+There is no checking of names of the client against the certificate
+Subject Name or Subject Alternate Names.
+
The difference between &%tls_verify_hosts%& and &%tls_try_verify_hosts%& is
what happens if the client does not supply a certificate, or if the certificate
does not match any of the certificates in the collection named by
certificate verification to the listed servers. Verification either must
or need not succeed respectively.
+The &%tls_verify_cert_hostnames%& option lists hosts for which additional
+checks are made: that the host name (the one in the DNS A record)
+is valid for the certificate.
+The option defaults to always checking.
+
The &(smtp)& transport has two OCSP-related options:
&%hosts_require_ocsp%&; a host-list for which a Certificate Status
is requested and required for the connection to proceed. The default
documentation is a good place to start; their SSL module's Introduction
document is currently at
.display
-.url(https://httpd.apache.org/docs/current/ssl/ssl_intro.html)
+&url(https://httpd.apache.org/docs/current/ssl/ssl_intro.html)
.endd
and their FAQ is at
.display
DANE-TA usage is effectively declaring a specific CA to be used; this might be a private CA or a public,
well-known one.
A private CA at simplest is just a self-signed certificate (with certain
-attributes) which is used to sign cerver certificates, but running one securely
+attributes) which is used to sign server certificates, but running one securely
does require careful arrangement.
With DANE-TA, as implemented in Exim and commonly in other MTAs,
the server TLS handshake must transmit the entire certificate chain from CA to server-certificate.
&%pipelining%&: A field is added to delivery and accept
log lines when the ESMTP PIPELINING extension was used.
The field is a single "L".
+
On accept lines, where PIPELINING was offered but not used by the client,
the field has a minus appended.
.next
.display
&`dane:fail `& failure reason
&`msg:delivery `& smtp confirmation message
+&`msg:fail:internal `& failure reason
+&`msg:fail:delivery `& smtp error message
&`msg:rcpt:host:defer `& error string
&`msg:rcpt:defer `& error string
&`msg:host:defer `& error string
projects / exim.git / blobdiff