section &<<SECTnamedlists>>&.
+.new
+.section "Builtin macros" "SECTbuiltinmacros"
+Exim defines some macros depending on facilities available, which may
+differ due to build-time definitions and from one release to another.
+All of these macros start with an underscore.
+They can be used to conditionally include parts of a configuration
+(see below).
+
+The following classes of macros are defined:
+.display
+&` _HAVE_ `& build-time defines
+&` _DRVR_AUTH_ `& authehticator drivers
+&` _DRVR_RTR_ `& router drivers
+&` _DRVR_TPT_ `& transport drivers
+&` _OPT_ `& configuration option support
+.endd
+
+Use an &"exim -bP macros"& command to get the list of macros.
+.wen
+
+
.section "Conditional skips in the configuration file" "SECID46"
.cindex "configuration file" "conditional skips"
.cindex "&`.ifdef`&"
See section &<<CALLaddparcall>>& for details of how this value is used.
-.option check_log_inodes main integer 0
+.new
+.option check_log_inodes main integer 100
+.wen
See &%check_spool_space%& below.
-.option check_log_space main integer 0
+.new
+.option check_log_space main integer 10M
+.wen
See &%check_spool_space%& below.
.oindex "&%check_rfc2047_length%&"
set false, Exim recognizes encoded words of any length.
-.option check_spool_inodes main integer 0
+.new
+.option check_spool_inodes main integer 100
+.wen
See &%check_spool_space%& below.
-.option check_spool_space main integer 0
+.new
+.option check_spool_space main integer 10M
+.wen
.cindex "checking disk space"
.cindex "disk space, checking"
.cindex "spool directory" "checking space"
.vindex "&$log_space$&"
.vindex "&$spool_inodes$&"
.vindex "&$spool_space$&"
-When any of these options are set, they apply to all incoming messages. If you
+When any of these options are nonzero, they apply to all incoming messages. If you
want to apply different checks to different kinds of message, you can do so by
testing the variables &$log_inodes$&, &$log_space$&, &$spool_inodes$&, and
&$spool_space$& in an ACL with appropriate additional conditions.
&%check_spool_space%& and &%check_spool_inodes%& check the spool partition if
either value is greater than zero, for example:
.code
-check_spool_space = 10M
+check_spool_space = 100M
check_spool_inodes = 100
.endd
The spool partition is the one that contains the directory defined by
&%check_spool_space%& is zero, unless &%no_smtp_check_spool_space%& is set.
The values for &%check_spool_space%& and &%check_log_space%& are held as a
-number of kilobytes. If a non-multiple of 1024 is specified, it is rounded up.
+number of kilobytes (though specified in bytes).
+If a non-multiple of 1024 is specified, it is rounded up.
For non-SMTP input and for batched SMTP input, the test is done at start-up; on
failure a message is written to stderr and Exim exits with a non-zero code, as
it obviously cannot send an error message of any kind.
+.new
+There is a slight performance penalty for these checks.
+Versions of Exim preceding 4.88 had these disabled by default;
+high-rate intallations confident they will never run out of resources
+may wish to deliberately disable them.
+.wen
+
.new
.option chunking_advertise_hosts main "host list&!!" *
.cindex CHUNKING advertisement
.option delay_warning main "time list" 24h
.cindex "warning of delay"
.cindex "delay warning, specifying"
+.cindex "queue" "delay warning"
When a message is delayed, Exim sends a warning message to the sender at
intervals specified by this option. The data is a colon-separated list of times
after which to send warning messages. If the value of the option is an empty
The value of this option is expanded and indicates the source of DH parameters
to be used by Exim.
-If it is a filename starting with a &`/`&, then it names a file from which DH
+.new
+&*Note: The Exim Maintainers strongly recommend using a filename with site-generated
+local DH parameters*&, which has been supported across all versions of Exim. The
+other specific constants available are a fallback so that even when
+"unconfigured", Exim can offer Perfect Forward Secrecy in older ciphersuites in TLS.
+.wen
+
+If &%tls_dhparam%& is a filename starting with a &`/`&,
+then it names a file from which DH
parameters should be loaded. If the file exists, it should hold a PEM-encoded
PKCS#3 representation of the DH prime. If the file does not exist, for
OpenSSL it is an error. For GnuTLS, Exim will attempt to create the file and
does not exist, Exim will attempt to create it.
See section &<<SECTgnutlsparam>>& for further details.
+.new
If Exim is using OpenSSL and this option is empty or unset, then Exim will load
-a default DH prime; the default is the 2048 bit prime described in section
+a default DH prime; the default is Exim-specific but lacks verifiable provenance.
+
+In older versions of Exim the default was the 2048 bit prime described in section
2.2 of RFC 5114, "2048-bit MODP Group with 224-bit Prime Order Subgroup", which
in IKE is assigned number 23.
Otherwise, the option must expand to the name used by Exim for any of a number
-of DH primes specified in RFC 2409, RFC 3526 and RFC 5114. As names, Exim uses
-"ike" followed by the number used by IKE, or "default" which corresponds to
-"ike23".
+of DH primes specified in RFC 2409, RFC 3526, RFC 5114, RFC 7919, or from other
+sources. As names, Exim uses a standard specified name, else "ike" followed by
+the number used by IKE, or "default" which corresponds to
+&`exim.dev.20160529.3`&.
-The available primes are:
+The available standard primes are:
+&`ffdhe2048`&, &`ffdhe3072`&, &`ffdhe4096`&, &`ffdhe6144`&, &`ffdhe8192`&,
&`ike1`&, &`ike2`&, &`ike5`&,
&`ike14`&, &`ike15`&, &`ike16`&, &`ike17`&, &`ike18`&,
-&`ike22`&, &`ike23`& (aka &`default`&) and &`ike24`&.
+&`ike22`&, &`ike23`& and &`ike24`&.
+
+The available additional primes are:
+&`exim.dev.20160529.1`&, &`exim.dev.20160529.2`& and &`exim.dev.20160529.3`&.
Some of these will be too small to be accepted by clients.
Some may be too large to be accepted by clients.
+The open cryptographic community has suspicions about the integrity of some
+of the later IKE values, which led into RFC7919 providing new fixed constants
+(the "ffdhe" identifiers).
+
+At this point, all of the "ike" values should be considered obsolete;
+they're still in Exim to avoid breaking unusual configurations, but are
+candidates for removal the next time we have backwards-incompatible changes.
+.wen
The TLS protocol does not negotiate an acceptable size for this; clients tend
to hard-drop connections if what is offered by the server is unacceptable,
projects / exim.git / blobdiff