transmit with DKIM

[exim.git] / doc / doc-docbook / spec.xfpt

diff --git a/doc/doc-docbook/spec.xfpt b/doc/doc-docbook/spec.xfpt
index 128aef3d139a593c9c63201737dad49b43f5b4fd..5c2c2ba118dc7af1c40da072d492bfcb594cb9ef 100644 (file)
--- a/doc/doc-docbook/spec.xfpt
+++ b/doc/doc-docbook/spec.xfpt
@@ -13801,6 +13801,7 @@ See also the &'Policy controls'& section above.
 .table2
 .row &%accept_8bitmime%&             "advertise 8BITMIME"
 .row &%auth_advertise_hosts%&        "advertise AUTH to these hosts"
+.row &%chunking_advertise_hosts%&    "advertise CHUNKING to these hosts"
 .row &%dsn_advertise_hosts%&         "advertise DSN extensions to these hosts"
 .row &%ignore_fromline_hosts%&       "allow &""From ""& from these hosts"
 .row &%ignore_fromline_local%&       "allow &""From ""& from local SMTP"
@@ -14358,6 +14359,13 @@ For non-SMTP input and for batched SMTP input, the test is done at start-up; on
 failure a message is written to stderr and Exim exits with a non-zero code, as
 it obviously cannot send an error message of any kind.
 
+.option chunking_advertise_hosts main "host list&!!" *
+.cindex CHUNKING advertisement
+.cindex "RFC 3030" "CHUNKING"
+The CHUNKING extension (RFC3030) will be advertised in the EHLO message to
+these hosts.
+Hosts may use the BDAT command as an alternate to DATA.
+
 .option daemon_smtp_ports main string &`smtp`&
 .cindex "port" "for daemon"
 .cindex "TCP/IP" "setting listening ports"
@@ -27741,6 +27749,15 @@ received, before the final response to the DATA command is sent. This is
 the ACL specified by &%acl_smtp_data%&, which is the second ACL that is
 associated with the DATA command.
 
+.cindex CHUNKING "BDAT command"
+.cindex BDAT "SMTP command"
+.cindex "RFC 3030" CHUNKING
+If CHUNKING was advertised and a BDAT command sequence is received,
+the &%acl_smtp_predata%& ACL is not run.
+.XXX why not?  It should be possible, for the first BDAT.
+The &%acl_smtp_data%& is run after the last BDAT command and all of
+the data specified is received.
+
 For both of these ACLs, it is not possible to reject individual recipients. An
 error response rejects the entire message. Unfortunately, it is known that some
 MTAs do not treat hard (5&'xx'&) responses to the DATA command (either
@@ -35620,10 +35637,12 @@ the following table:
 &`F   `&        sender address (on delivery lines)
 &`H   `&        host name and IP address
 &`I   `&        local interface used
+&`K   `&        CHUNKING extension used
 &`id  `&        message id for incoming message
 &`P   `&        on &`<=`& lines: protocol used
 &`    `&        on &`=>`& and &`**`& lines: return path
-&`PRX `&        on &'<='& and&`=>`& lines: proxy address
+&`PRDR`&        PRDR extension used
+&`PRX `&        on &'<='& and &`=>`& lines: proxy address
 &`Q   `&        alternate queue name
 &`QT  `&        on &`=>`& lines: time spent on queue so far
 &`    `&        on &"Completed"& lines: time spent on queue
@@ -38115,7 +38134,7 @@ used.
 .section "Verifying DKIM signatures in incoming mail" "SECID514"
 .cindex "DKIM" "verification"
 
-Verification of DKIM signatures in incoming email is implemented via the
+Verification of DKIM signatures in SMTP incoming email is implemented via the
 &%acl_smtp_dkim%& ACL. By default, this ACL is called once for each
 syntactically(!) correct signature in the incoming message.
 A missing ACL definition defaults to accept.