. /////////////////////////////////////////////////////////////////////////////
. These definitions set some parameters and save some typing.
+. Update the Copyright year (only) when changing content.
. /////////////////////////////////////////////////////////////////////////////
.set previousversion "4.80"
.set ACL "access control lists (ACLs)"
.set I " "
+.macro copyyear
+2012
+.endmacro
. /////////////////////////////////////////////////////////////////////////////
. Additional xfpt markup used by this document, over and above the default
<authorinitials>EM</authorinitials>
</revision></revhistory>
<copyright><year>
-.year
+.copyyear
</year><holder>University of Cambridge</holder></copyright>
</bookinfo>
.literal off
It sets the incoming protocol and host name (for trusted callers). The
host name and its colon can be omitted when only the protocol is to be set.
Note the Exim already has two private options, &%-pd%& and &%-ps%&, that refer
-to embedded Perl. It is therefore impossible to set a protocol value of &`p`&
+to embedded Perl. It is therefore impossible to set a protocol value of &`d`&
or &`s`& using this option (but that does not seem a real limitation).
.vitem &%-q%&
.vindex "&$return_size_limit$&"
This is an obsolete name for &$bounce_return_size_limit$&.
+.vitem &$router_name$&
+.cindex "router" "name"
+.cindex "name" "of router"
+.vindex "&$router_name$&"
+During the running of a router this variable contains its name.
+
.vitem &$runrc$&
.cindex "return code" "from &%run%& expansion"
.vindex "&$runrc$&"
This variable contains the UTC date and time in &"Zulu"& format, as specified
by ISO 8601, for example: 20030221154023Z.
+.vitem &$transport_name$&
+.cindex "transport" "name"
+.cindex "name" "of transport"
+.vindex "&$transport_name$&"
+During the running of a transport, this variable contains its name.
+
.vitem &$value$&
.vindex "&$value$&"
This variable contains the result of an expansion lookup, extraction operation,
See &<<SECTtlssni>>& for discussion of when this option might be re-expanded.
+A forced expansion failure or setting to an empty string is equivalent to
+being unset.
+
.option tls_verify_hosts main "host list&!!" unset
.cindex "TLS" "client certificate verification"
.option debug_print routers string&!! unset
.cindex "testing" "variables in drivers"
If this option is set and debugging is enabled (see the &%-d%& command line
-option), the string is expanded and included in the debugging output.
+option) or in address-testing mode (see the &%-bt%& command line option),
+the string is expanded and included in the debugging output.
If expansion of the string fails, the error message is written to the debugging
output, and Exim carries on processing.
This option is provided to help with checking out the values of variables and
variables it references. The output happens after checks for &%domains%&,
&%local_parts%&, and &%check_local_user%& but before any other preconditions
are tested. A newline is added to the text if it does not end with one.
+The variable &$router_name$& contains the name of the router.
option is not working properly, &%debug_print%& could be used to output the
variables it references. A newline is added to the text if it does not end with
one.
+The variables &$transport_name$& and &$router_name$& contain the name of the
+transport and the router that called it.
.option delivery_date_add transports boolean false
.vindex "&$address_pipe$&"
A router redirects an address directly to a pipe command (for example, from an
alias or forward file). In this case, &$address_pipe$& contains the text of the
-pipe command, and the &%command%& option on the transport is ignored. If only
-one address is being transported (&%batch_max%& is not greater than one, or
-only one address was redirected to this pipe command), &$local_part$& contains
-the local part that was redirected.
+pipe command, and the &%command%& option on the transport is ignored unless
+&%force_command%& is set. If only one address is being transported
+(&%batch_max%& is not greater than one, or only one address was redirected to
+this pipe command), &$local_part$& contains the local part that was redirected.
.endlist
avoids any problems with spaces or shell metacharacters, and is of use when a
&(pipe)& transport is handling groups of addresses in a batch.
+If &%force_command%& is enabled on the transport, Special handling takes place
+for an argument that consists of precisely the text &`$address_pipe`&. It
+is handled similarly to &$pipe_addresses$& above. It is expanded and each
+argument is inserted in the argument list at that point
+&'as a separate argument'&. The &`$address_pipe`& item does not need to be
+the only item in the argument; in fact, if it were then &%force_command%&
+should behave as a no-op. Rather, it should be used to adjust the command
+run while preserving the argument vector separation.
+
After splitting up into arguments and expansion, the resulting command is run
in a subprocess directly from the transport, &'not'& under a shell. The
message that is being delivered is supplied on the standard input, and the
frozen in Exim's queue instead.
+.option force_command pipe boolean false
+.cindex "force command"
+.cindex "&(pipe)& transport", "force command"
+Normally when a router redirects an address directly to a pipe command
+the &%command%& option on the transport is ignored. If &%force_command%&
+is set, the &%command%& option will used. This is especially
+useful for forcing a wrapper or additional argument to be added to the
+command. For example:
+.code
+command = /usr/bin/remote_exec myhost -- $address_pipe
+force_command
+.endd
+
+Note that &$address_pipe$& is handled specially in &%command%& when
+&%force_command%& is set, expanding out to the original argument vector as
+separate items, similarly to a Unix shell &`"$@"`& construct.
+
.option ignore_status pipe boolean false
If this option is true, the status returned by the subprocess that is set up to
run the command is ignored, and Exim behaves as if zero had been returned.
Edit &_src/drtables.c_&, adding conditional code to pull in the private header
and create a table entry as is done for all the other drivers and lookup types.
.next
+Edit &_scripts/lookups-Makefile_& if this is a new lookup; there is a for-loop
+near the bottom, ranging the &`name_mod`& variable over a list of all lookups.
+Add your &`NEWDRIVER`& to that list.
+As long as the dynamic module would be named &_newdriver.so_&, you can use the
+simple form that most lookups have.
+.next
Edit &_Makefile_& in the appropriate sub-directory (&_src/routers_&,
&_src/transports_&, &_src/auths_&, or &_src/lookups_&); add a line for the new
driver or lookup type and add it to the definition of OBJ.
projects / exim.git / blobdiff