release process: fix stupid bug for quick/non-quick release
[exim.git] / src / README.UPDATING
CommitLineData
0f4f2a88
PH
1This document contains detailed information about incompatibilities that might
2be encountered when upgrading from one release of Exim to another. The
3information is in reverse order of release numbers. Mostly these are relatively
4small points, and the configuration file is normally upwards compatible, but
5there have been two big upheavals...
6
7
8**************************************************************************
9* There was a big reworking of the way mail routing works for release *
10* 4.00. Previously used "directors" were abolished, and all routing is *
11* now done by routers. Policy controls for incoming mail are now done by *
12* Access Control Lists instead of separate options. All this means that *
13* pre-4.00 configuration files have to be massively converted. If you *
14* are coming from a 3.xx release, please read the document in the file *
15* doc/Exim4.upgrade, and allow some time to complete the upgrade. *
16* *
17* There was a big reworking of the way domain/host/net/address lists are *
18* handled at release 3.00. If you are coming from a pre-3.00 release, it *
19* might be easier to start again from a default configuration. Otherwise *
20* you need to read doc/Exim3.upgrade and do a double conversion of your *
21* configuration file. *
22**************************************************************************
23
24
25The rest of this document contains information about changes in 4.xx releases
26that might affect a running system.
2eda48c6 27
e6acf885 28
d8d9f930
JH
29Exim version 4.92
30-----------------
31
32 * Exim used to manually follow CNAME chains, to a limited depth. In this
33 day-and-age we expect the resolver to be doing this for us, so the loop
34 is limited to one retry unless the (new) config option dns_cname_loops
35 is changed.
36
1f791335
PP
37Exim version 4.91
38-----------------
39
40 * DANE and SPF have been promoted from Experimental to Supported status, thus
41 the options to enable them in Local/Makefile have been renamed.
42 See current src/EDITME for full details, including changes in dependencies,
43 but loosely: replace EXPERIMENTAL_SPF with SUPPORT_SPF and replace
44 EXPERIMENTAL_DANE with SUPPORT_DANE.
45
46 * Ancient ClamAV stream support, long deprecated by ClamAV, has been removed;
47 if you were building with WITH_OLD_CLAMAV_STREAM enabled then your problems
48 have marginally increased.
49
50 * A number of logging changes; if relying upon the previous DKIM additional
51 log-line, explicit log_selector configuration is needed to keep it.
52
53 * Other incompatible changes in EXPERIMENTAL_* features, read NewStuff and
54 ChangeLog carefully if relying upon an experimental feature such as DMARC.
55 Note that this includes changes to SPF as it was promoted into Supported.
56
57
2eec84ca
PP
58Exim version 4.89
59-----------------
60
7dc5f827
PP
61 * SMTP CHUNKING in Exim 4.88 did not ensure that received mails had a final
62 newline; attempts to deliver such messages onwards to non-chunking hosts
63 would probably hang, as Exim does not insert the newline before a ".".
64 In 4.89, the newline is added upon receipt. For already-received messages
65 in your queue, try util/chunking_fixqueue_finalnewlines.pl
66 to walk the queue, fixing any affected messages. Note that because a
67 delivery attempt will be hanging, attempts to lock the messages for fixing
68 them will stall; stopping all queue-runners temporarily is recommended.
69
2eec84ca
PP
70 * OpenSSL: oldest supported release series is now 1.0.2, which is the oldest
71 supported by the OpenSSL project. If you can build Exim with an older
72 release series, congratulations. If you can't, then upgrade.
73 The file doc/openssl.txt contains instructions for installing a current
74 OpenSSL outside the system library paths and building Exim to use it.
75
0aaf76a4
PP
76 * FreeBSD: we now always use the system iconv in libc, as all versions of
77 FreeBSD supported by the FreeBSD project provide this functionality.
78
2eec84ca 79
f59aaaaa
PP
80Exim version 4.88
81-----------------
82
83 * The "demime" ACL condition, deprecated for the past 10 years, has
84 now been removed.
85
86 * Old GnuTLS configuration options "gnutls_require_kx", "gnutls_require_mac",
87 and "gnutls_require_protocols" have now been removed. (Inoperative from
88 4.80, per below; logging warnings since 4.83, again per below).
89
90
c50e5871
JH
91Exim version 4.83
92-----------------
93
94 * SPF condition results renamed "permerror" and "temperror". The old
aded2255 95 names are still accepted for back-compatibility, for this release.
c50e5871
JH
96
97 * TLS details are now logged on rejects, subject to log selectors.
98
99 * Items in headers_remove lists must now have any embedded list-separators
100 doubled.
101
102 * Attempted use of the deprecated options "gnutls_require_kx" et. al.
103 now result in logged warning.
104
105
2c422e6f 106Exim version 4.82
a5f239e4
PP
107-----------------
108
2519e60d 109 * New option gnutls_allow_auto_pkcs11 defaults false; if you have GnuTLS 2.12.0
a5f239e4
PP
110 or later and do want PKCS11 modules to be autoloaded, then set this option.
111
8b260705
PP
112 * A per-transport wait-<name> database is no longer updated if the transport
113 sets "connection_max_messages" to 1, as it can not be used and causes
114 unnecessary serialisation and load. External tools tracking the state of
115 Exim by the hints databases may need modification to take this into account.
116
b10e4ec2
TL
117 * The av_scanner option can now accept multiple clamd TCP targets, all other
118 setting limitations remain.
119
a5f239e4 120
83e2f8a2 121Exim version 4.80
dec5017e
PP
122-----------------
123
83e2f8a2
PP
124 * BEWARE backwards-incompatible changes in SSL libraries, thus the version
125 bump. See points below for details.
c2b063d4 126 Also an LDAP data returned format change.
83e2f8a2 127
dec5017e
PP
128 * The value of $tls_peerdn is now print-escaped when written to the spool file
129 in a -tls_peerdn line, and unescaped when read back in. We received reports
130 of values with embedded newlines, which caused spool file corruption.
131
132 If you have a corrupt spool file and you wish to recover the contents after
133 upgrading, then lock the message, replace the new-lines that should be part
134 of the -tls_peerdn line with the two-character sequence \n and then unlock
135 the message. No tool has been provided as we believe this is a rare
aded2255 136 occurrence.
dec5017e 137
f0f5a555
PP
138 * For OpenSSL, SSLv2 is now disabled by default. (GnuTLS does not support
139 SSLv2). RFC 6176 prohibits SSLv2 and some informal surveys suggest no
140 actual usage. You can re-enable with the "openssl_options" Exim option,
141 in the main configuration section. Note that supporting SSLv2 exposes
142 you to ciphersuite downgrade attacks.
143
c80c5570
PP
144 * With OpenSSL 1.0.1+, Exim now supports TLS 1.1 and TLS 1.2. If built
145 against 1.0.1a then you will get a warning message and the
146 "openssl_options" value will not parse "no_tlsv1_1": the value changes
147 incompatibly between 1.0.1a and 1.0.1b, because the value chosen for 1.0.1a
148 is infelicitous. We advise avoiding 1.0.1a.
149
150 "openssl_options" gains "no_tlsv1_1", "no_tlsv1_2" and "no_compression".
151
da3ad30d 152 COMPATIBILITY WARNING: The default value of "openssl_options" is no longer
f0f5a555
PP
153 "+dont_insert_empty_fragments". We default to "+no_sslv2".
154 That old default was grandfathered in from before openssl_options became a
155 configuration option.
da3ad30d
PP
156 Empty fragments are inserted by default through TLS1.0, to partially defend
157 against certain attacks; TLS1.1+ change the protocol so that this is not
158 needed. The DIEF SSL option was required for some old releases of mail
159 clients which did not gracefully handle the empty fragments, and was
160 initially set in Exim release 4.31 (see ChangeLog, item 37).
161
162 If you still have affected mail-clients, and you see SSL protocol failures
163 with this release of Exim, set:
164 openssl_options = +dont_insert_empty_fragments
165 in the main section of your Exim configuration file. You're trading off
166 security for compatibility. Exim is now defaulting to higher security and
167 rewarding more modern clients.
168
3375e053
PP
169 If the option tls_dhparams is set and the parameters loaded from the file
170 have a bit-count greater than the new option tls_dh_max_bits, then the file
171 will now be ignored. If this affects you, raise the tls_dh_max_bits limit.
172 We suspect that most folks are using dated defaults and will not be affected.
173
5407bfff
JH
174 * Ldap lookups returning multi-valued attributes now separate the attributes
175 with only a comma, not a comma-space sequence. Also, an actual comma within
176 a returned attribute is doubled. This makes it possible to parse the
177 attribute as a comma-separated list. Note the distinction from multiple
178 attributes being returned, where each one is a name=value pair.
c80c5570 179
c2b063d4
PP
180 If you are currently splitting the results from LDAP upon a comma, then you
181 should check carefully to see if adjustments are needed.
182
183 This change lets cautious folks distinguish "comma used as separator for
184 joining values" from "comma inside the data".
185
9cbad13b
PP
186 * accept_8bitmime now defaults on, which is not RFC compliant but is better
187 suited to today's Internet. See http://cr.yp.to/smtp/8bitmime.html for a
188 sane rationale. Those who wish to be strictly RFC compliant, or know that
189 they need to talk to servers that are not 8-bit-clean, now need to take
190 explicit configuration action to default this option off. This is not a
191 new option, you can safely force it off before upgrading, to decouple
192 configuration changes from the binary upgrade while remaining RFC compliant.
193
f90a9fd1
PP
194 * The GnuTLS support has been mostly rewritten, to use APIs which don't cause
195 deprecation warnings in GnuTLS 2.12.x. As part of this, these three options
196 are no longer supported:
17c76198
PP
197
198 gnutls_require_kx
199 gnutls_require_mac
200 gnutls_require_protocols
201
f90a9fd1
PP
202 Their functionality is entirely subsumed into tls_require_ciphers. In turn,
203 tls_require_ciphers is no longer an Exim list and is not parsed by Exim, but
204 is instead given to gnutls_priority_init(3), which expects a priority string;
205 this behaviour is much closer to the OpenSSL behaviour. See:
17c76198 206
42bfef1e 207 http://www.gnutls.org/manual/html_node/Priority-Strings.html
17c76198
PP
208
209 for fuller documentation of the strings parsed. The three gnutls_require_*
210 options are still parsed by Exim and, for this release, silently ignored.
211 A future release will add warnings, before a later still release removes
212 parsing entirely and the presence of the options will be a configuration
213 error.
214
83e2f8a2
PP
215 Note that by default, GnuTLS will not accept RSA-MD5 signatures in chains.
216 A tls_require_ciphers value of NORMAL:%VERIFY_ALLOW_SIGN_RSA_MD5 may
217 re-enable support, but this is not supported by the Exim maintainers.
218 Our test suite no longer includes MD5-based certificates.
219
17c76198
PP
220 This rewrite means that Exim will continue to build against GnuTLS in the
221 future, brings Exim closer to other GnuTLS applications and lets us add
222 support for SNI and other features more readily. We regret that it wasn't
223 feasible to retain the three dropped options.
224
3375e053
PP
225 * If built with TLS support, then Exim will now validate the value of
226 the main section tls_require_ciphers option at start-up. Before, this
227 would cause a STARTTLS 4xx failure, now it causes a failure to start.
228 Running with a broken configuration which causes failures that may only
229 be left in the logs has been traded off for something more visible. This
230 change makes an existing problem more prominent, but we do not believe
231 anyone would deliberately be running with an invalid tls_require_ciphers
232 option.
233
234 This also means that library linkage issues caused by conflicts of some
235 kind might take out the main daemon, not just the delivery or receiving
236 process. Conceivably some folks might prefer to continue delivering
237 mail plaintext when their binary is broken in this way, if there is a
238 server that is a candidate to receive such mails that does not advertise
239 STARTTLS. Note that Exim is typically a setuid root binary and given
240 broken linkage problems that cause segfaults, we feel it is safer to
241 fail completely. (The check is not done as root, to ensure that problems
242 here are not made worse by the check).
243
a799883d
PP
244 * The "tls_dhparam" option has been updated, so that it can now specify a
245 path or an identifier for a standard DH prime from one of a few RFCs.
246 The default for OpenSSL is no longer to not use DH but instead to use
247 one of these standard primes. The default for GnuTLS is no longer to use
248 a file in the spool directory, but to use that same standard prime.
249 The option is now used by GnuTLS too. If it points to a path, then
250 GnuTLS will use that path, instead of a file in the spool directory;
251 GnuTLS will attempt to create it if it does not exist.
252
253 To preserve the previous behaviour of generating files in the spool
254 directory, set "tls_dhparam = historic". Since prior releases of Exim
255 ignored tls_dhparam when using GnuTLS, this can safely be done before
256 the upgrade.
257
258
dec5017e 259
c566dd90
PP
260Exim version 4.77
261-----------------
262
263 * GnuTLS will now attempt to use TLS 1.2 and TLS 1.1 before TLS 1.0 and SSL3,
264 if supported by your GnuTLS library. Use the existing
265 "gnutls_require_protocols" option to downgrade this if that will be a
266 problem. Prior to this release, supported values were "TLS1" and "SSL3",
267 so you should be able to update configuration prior to update.
268
0215ec07
PP
269 [nb: gnutls_require_protocols removed in Exim 4.80, instead use
270 tls_require_ciphers to provide a priority string; see notes above]
271
39257585
PP
272 * The match_<type>{string1}{string2} expansion conditions no longer subject
273 string2 to string expansion, unless Exim was built with the new
274 "EXPAND_LISTMATCH_RHS" option. Too many people have inadvertently created
275 insecure configurations that way. If you need the functionality and turn on
276 that build option, please let the developers know, and know why, so we can
277 try to provide a safer mechanism for you.
278
a7ee5955
PP
279 The match{}{} expansion condition (for regular expressions) is NOT affected.
280 For match_<type>{s1}{s2}, all list functionality is unchanged. The only
281 change is that a '$' appearing in s2 will not trigger expansion, but instead
282 will be treated as a literal $ sign; the effect is very similar to having
283 wrapped s2 with \N...\N. If s2 contains a named list and the list definition
284 uses $expansions then those _will_ be processed as normal. It is only the
285 point at which s2 is read where expansion is inhibited.
286
287 If you are trying to test if two email addresses are equal, use eqi{s1}{s2}.
288 If you are testing if the address in s1 occurs in the list of items given
289 in s2, either use the new inlisti{s1}{s2} condition (added in 4.77) or use
290 the pre-existing forany{s2}{eqi{$item}{s1}} condition.
291
c566dd90 292
e6acf885
PP
293Exim version 4.74
294-----------------
295
4050a044
PP
296 * The integrated support for dynamically loadable lookup modules has an ABI
297 change from the modules supported by some OS vendors through an unofficial
298 patch. Don't try to mix & match.
299
300 * Some parts of the build system are now beginning to assume that the host
301 environment is POSIX. If you're building on a system where POSIX tools are
302 not the default, you might have an easier time if you switch to the POSIX
303 tools. Feel free to report non-POSIX issues as a request for a feature
304 enhancement, but if the POSIX variants are available then the fix will
305 probably just involve some coercion. See the README instructions for
306 building on such hosts.
e6acf885
PP
307
308
309Exim version 4.73
310-----------------
311
312 * The Exim run-time user can no longer be root; this was always
313 strongly discouraged, but is now prohibited both at build and
314 run-time. If you need Exim to run routinely as root, you'll need to
315 patch the source and accept the risk. Here be dragons.
316
317 * Exim will no longer accept a configuration file owned by the Exim
318 run-time user, unless that account is explicitly the value in
319 CONFIGURE_OWNER, which we discourage. Exim now checks to ensure that
a7ee5955 320 files are not writeable by other accounts.
e6acf885
PP
321
322 * The ALT_CONFIG_ROOT_ONLY build option is no longer optional and is forced
323 on; the Exim user can, by default, no longer use -C/-D and retain privilege.
324 Two new build options mitigate this.
325
326 * TRUSTED_CONFIG_LIST defines a file containing a whitelist of config
327 files that are trusted to be selected by the Exim user; one per line.
328 This is the recommended approach going forward.
329
330 * WHITELIST_D_MACROS defines a colon-separated list of macro names which
331 the Exim run-time user may safely pass without dropping privileges.
332 Because changes to this involve a recompile, this is not the recommended
333 approach but may ease transition. The values of the macros, when
43236f35 334 overridden, are constrained to match this regex: ^[A-Za-z0-9_/.-]*$
e6acf885
PP
335
336 * The system_filter_user option now defaults to the Exim run-time user,
337 rather than root. You can still set it explicitly to root and this
338 can be done with prior versions too, letting you roll versions
339 without needing to change this configuration option.
340
341 * ClamAV must be at least version 0.95 unless WITH_OLD_CLAMAV_STREAM is
342 defined at build time.
343
344
2eda48c6
TK
345Exim version 4.70
346-----------------
347
3481. Experimental Yahoo! Domainkeys support has been dropped in this release.
aded2255 349It has been superseded by a native implementation of its successor DKIM.
2eda48c6
TK
350
3512. Up to version 4.69, Exim came with an embedded version of the PCRE library.
352As of 4.70, this is no longer the case. To compile Exim, you will need PCRE
a7ee5955 353installed. Most OS distributions have ready-made library and development
2eda48c6 354packages.
0f4f2a88
PH
355
356
3c223874
PH
357Exim version 4.68
358-----------------
359
3601. The internal implementation of the database keys that are used for ACL
361ratelimiting has been tidied up. This means that an update to 4.68 might cause
362Exim to "forget" previous rates that it had calculated, and reset them to zero.
363
364
26da7e20
PH
365Exim version 4.64
366-----------------
367
3681. Callouts were setting the name used for EHLO/HELO from $smtp_active_
369hostname. This is wrong, because it relates to the incoming message (and
370probably the interface on which it is arriving) and not to the outgoing
371callout (which could be using a different interface). This has been
372changed to use the value of the helo_data option from the smtp transport
373instead - this is what is used when a message is actually being sent. If
374there is no remote transport (possible with a router that sets up host
375addresses), $smtp_active_hostname is used. This change is mentioned here in
376case somebody is relying on the use of $smtp_active_hostname.
377
ebc9d865
PH
3782. A bug has been fixed that might just possibly be something that is relied on
379in some configurations. In expansion items such as ${if >{xxx}{yyy}...} an
380empty string (that is {}) was being interpreted as if it was {0} and therefore
381treated as the number zero. From release 4.64, such strings cause an error
382because a decimal number, possibly followed by K or M, is required (as has
383always been documented).
384
b6c27e28
PH
3853. There has been a change to the GnuTLS support (ChangeLog/PH/20) to improve
386Exim's performance. Unfortunately, this has the side effect of being slightly
387non-upwards compatible for versions 4.50 and earlier. If you are upgrading from
388one of these earlier versions and you use GnuTLS, you must remove the file
389called gnutls-params in Exim's spool directory. If you don't do this, you will
390see this error:
391
392 TLS error on connection from ... (DH params import): Base64 decoding error.
393
394Removing the file causes Exim to recompute the relevant encryption parameters
395and cache them in the new format that was introduced for release 4.51 (May
3962005). If you are upgrading from release 4.51 or later, there should be no
397problem.
398
26da7e20 399
a5bd321b
PH
400Exim version 4.63
401-----------------
402
403When an SMTP error message is specified in a "message" modifier in an ACL, or
404in a :fail: or :defer: message in a redirect router, Exim now checks the start
405of the message for an SMTP error code. This consists of three digits followed
406by a space, optionally followed by an extended code of the form n.n.n, also
407followed by a space. If this is the case and the very first digit is the same
408as the default error code, the code from the message is used instead. If the
409very first digit is incorrect, a panic error is logged, and the default code is
410used. This is an incompatible change, but it is not expected to affect many (if
411any) configurations. It is possible to suppress the use of the supplied code in
412a redirect router by setting the smtp_error_code option false. In this case,
413any SMTP code is quietly ignored.
414
415
47ca6d6c
PH
416Exim version 4.61
417-----------------
418
8def5aaf
PH
4191. The default number of ACL variables of each type has been increased to 20,
420and it's possible to compile Exim with more. You can safely upgrade to this
421release if you already have messages on the queue with saved ACL variable
422values. However, if you downgrade from this release with messages on the queue,
423any saved ACL values they may have will be lost.
424
4252. The default value for rfc1413_query_timeout has been changed from 30s to 5s.
47ca6d6c
PH
426
427
8857ccfd
PH
428Exim version 4.54
429-----------------
430
431There was a problem with 4.52/TF/02 in that a "name=" option on control=
432submission terminated at the next slash, thereby not allowing for slashes in
433the name. This has been changed so that "name=" takes the rest of the string as
434its data. It must therefore be the last option.
435
436
f3f0a1f0
PH
437Version 4.53
438------------
439
440If you are using the experimental Domain Keys support, you must upgrade to
441at least libdomainkeys 0.67 in order to run this release of Exim.
442
443
b5aea5e1
PH
444Version 4.51
445------------
446
c688b954
PH
4471. The format in which GnuTLS parameters are cached (in the file gnutls-params
448in the spool directory) has been changed. The new format can also be generated
b5aea5e1
PH
449externally, so it is now possible to update the values from outside Exim. This
450has been implemented in an upwards, BUT NOT downwards, compatible manner.
451Upgrading should be seamless: when Exim finds that it cannot understand an
452existing cache file, it generates new parameters and writes them to the cache
453in the new format. If, however, you downgrade from 4.51 to a previous release,
454you MUST delete the gnutls-params file in the spool directory, because the
455older Exim will not recognize the new format.
456
c688b954
PH
4572. When doing a callout as part of verifying an address, Exim was not paying
458attention to any local part prefix or suffix that was matched by the router
459that accepted the address. It now behaves in the same way as it does for
460delivery: the affixes are removed from the local part unless
461rcpt_include_affixes is set on the transport. If you have a configuration that
462uses prefixes or suffixes on addresses that could be used for callouts, and you
463want the affixes to be retained, you must make sure that rcpt_include_affixes
464is set on the transport.
465
447d236c
PH
4663. Bounce and delay warning messages no longer contain details of delivery
467errors, except for explicit messages (e.g. generated by :fail:) and SMTP
468responses from remote hosts.
469
b5aea5e1 470
8b5af54d
PH
471Version 4.50
472------------
473
4964e932
PH
474The exicyclog script has been updated to use three-digit numbers in rotated log
475files if the maximum number to keep is greater than 99. If you are already
476keeping more than 99, there will be an incompatible change when you upgrade.
477You will probably want to rename your old log files to the new form before
c3af992c 478running the new exicyclog.
8b5af54d
PH
479
480
0f4f2a88
PH
481Version 4.42
482------------
483
484RFC 3848 specifies standard names for the "with" phrase in Received: header
485lines when AUTH and/or TLS are in use. This is the "received protocol"
486field. Exim used to use "asmtp" for authenticated SMTP, without any
487indication (in the protocol name) for TLS use. Now it follows the RFC and
488uses "esmtpa" if the connection is authenticated, "esmtps" if it is
489encrypted, and "esmtpsa" if it is both encrypted and authenticated. These names
490appear in log lines as well as in Received: header lines.
491
492
493Version 4.34
494------------
495
496Change 4.31/2 gave problems to data ACLs and local_scan() functions that
497expected to see a Received: header. I have changed to yet another scheme. The
498Received: header is now generated after the body is received, but before the
499ACL or local_scan() is called. After they have run, the timestamp in the
500Received: header is updated.
501
502Thus, change (a) of 4.31/2 has been reversed, but change (b) is still true,
503which is lucky, since I decided it was a bug fix.
504
505
506Version 4.33
507------------
508
509If an expansion in a condition on a "warn" statement fails because a lookup
510defers, the "warn" statement is abandoned, and the next ACL statement is
511processed. Previously this caused the whole ACL to be aborted.
512
513
514Version 4.32
515------------
516
517Change 4.31/2 has been reversed, as it proved contentious. Recipient callout
518verification now uses <> in the MAIL command by default, as it did before. A
519new callout option, "use_sender", has been added to request the other
520behaviour.
521
522
523Version 4.31
524------------
525
5261. If you compile Exim to use GnuTLS, it now requires the use of release 1.0.0
527 or greater. The interface to the obsolete 0.8.x releases is no longer
528 supported. There is one externally visible change: the format for the
529 display of Distinguished Names now uses commas as a separator rather than a
530 slash. This is to comply with RFC 2253.
531
5322. When a message is received, the Received: header line is now generated when
533 reception is complete, instead of at the start of reception. For messages
534 that take a long time to come in, this changes the meaning of the timestamp.
535 There are several side-effects of this change:
536
537 (a) If a message is rejected by a DATA or non-SMTP ACL, or by local_scan(),
538 the logged header lines no longer include the local Received: line,
539 because it has not yet been created. If the message is a non-SMTP one,
540 and the error is processed by sending a message to the sender, the copy
541 of the original message that is returned does not have an added
542 Received: line.
543
544 (b) When a filter file is tested using -bf, no additional Received: header
545 is added to the test message. After some thought, I decided that this
546 is a bug fix.
547
548 The contents of $received_for are not affected by this change. This
549 variable still contains the single recipient of a message, copied after
550 addresses have been rewritten, but before local_scan() is run.
551
5522. Recipient callout verification, like sender verification, was using <> in
553 the MAIL FROM command. This isn't really the right thing, since the actual
554 sender may affect whether the remote host accepts the recipient or not. I
555 have changed it to use the actual sender in the callout; this means that
556 the cache record is now keyed on a recipient/sender pair, not just the
557 recipient address. There doesn't seem to be a real danger of callout loops,
558 since a callout by the remote host to check the sender would use <>.
559
560
561Version 4.30
562------------
563
5641. I have abolished timeout_DNS as an error that can be detected in retry
565 rules, because it has never worked. Despite the fact that it has been
566 documented since at least release 1.62, there was no code to support it.
567 If you have used it in your retry rules, you will now get a warning message
568 to the log and panic log. It is now treated as plain "timeout".
569
5702. After discussion on the mailing list, Exim no longer adds From:, Date:, or
571 Message-Id: header lines to messages that do not originate locally, that is,
572 messages that have an associated sending host address.
573
5743. When looking up a host name from an IP address, Exim now tries the DNS
575 first, and only if that fails does it use gethostbyaddr() (or equivalent).
576 This change was made because on some OS, not all the names are given for
577 addresses with multiple PTR records via the gethostbyaddr() interface. The
578 order of lookup can be changed by setting host_lookup_order.
579
580
581Version 4.23
582------------
583
5841. The new FIXED_NEVER_USERS build-time option creates a list of "never users"
585 that cannot be overridden. The default in the distributed EDITME is "root".
586 If for some reason you were (against advice) running deliveries as root, you
587 will have to ensure that FIXED_NEVER_USERS is not set in your
588 Local/Makefile.
589
5902. The ${quote: operator now quotes an empty string, which it did not before.
591
5923. Version 4.23 saves the contents of the ACL variables with the message, so
593 that they can be used later. If one of these variables contains a newline,
594 there will be a newline character in the spool that will not be interpreted
4c04137d 595 correctly by a previous version of Exim. (Exim ignores keyed spool file
0f4f2a88
PH
596 items that it doesn't understand - precisely for this kind of problem - but
597 it expects them all to be on one line.)
598
599 So the bottom line is: if you have newlines in your ACL variables, you
600 cannot retreat from 4.23.
601
602
603Version 4.21
604------------
605
6061. The idea of the "warn" ACL verb is that it adds a header or writes to the
607 log only when "message" or "log_message" are set. However, if one of the
608 conditions was an address verification, or a call to a nested ACL, the
609 messages generated by the underlying test were being passed through. This
610 no longer happens. The underlying message is available in $acl_verify_
611 message for both "message" and "log_message" expansions, so it can be
612 passed through if needed.
613
6142. The way that the $h_ (and $header_) expansions work has been changed by the
615 addition of RFC 2047 decoding. See the main documentation (the NewStuff file
616 until release 4.30, then the manual) for full details. Briefly, there are
617 now three forms:
618
619 $rh_xxx: and $rheader_xxx: give the original content of the header
620 line(s), with no processing at all.
621
622 $bh_xxx: and $bheader_xxx: remove leading and trailing white space, and
623 then decode base64 or quoted-printable "words" within the header text,
624 but do not do charset translation.
625
626 $h_xxx: and $header_xxx: attempt to translate the $bh_ string to a
627 standard character set.
628
629 If you have previously been using $h_ expansions to access the raw
630 characters, you should change to $rh_ instead.
631
6323. When Exim creates an RFC 2047 encoded word in a header line, it labels it
633 with the default character set from the headers_charset option instead of
634 always using iso-8859-1.
635
6364. If TMPDIR is defined in Local/Makefile (default in src/EDITME is
637 TMPDIR="/tmp"), Exim checks for the presence of an environment variable
638 called TMPDIR, and if it finds it is different, it changes its value.
639
6405. Following a discussion on the list, the rules by which Exim recognises line
641 endings on incoming messages have been changed. The -dropcr and drop_cr
642 options are now no-ops, retained only for backwards compatibility. The
643 following line terminators are recognized: LF CRLF CR. However, special
644 processing applies to CR:
645
646 (i) The sequence CR . CR does *not* terminate an incoming SMTP message,
647 nor a local message in the state where . is a terminator.
648
649 (ii) If a bare CR is encountered in a header line, an extra space is added
650 after the line terminator so as not to end the header. The reasoning
651 behind this is that bare CRs in header lines are most likely either
652 to be mistakes, or people trying to play silly games.
653
6546. The code for using daemon_smtp_port, local_interfaces, and the -oX options
655 has been reorganized. It is supposed to be backwards compatible, but it is
656 mentioned here just in case I've screwed up.
657
658
659
660Version 4.20
661------------
662
6631. I have tidied and re-organized the code that uses alarm() for imposing time
664 limits on various things. It shouldn't affect anything, but if you notice
665 processes getting stuck, it may be that I've broken something.
666
6672. The "arguments" log selector now also logs the current working directory
668 when Exim is called.
669
6703. An incompatible change has been made to the appendfile transport. This
671 affects the case when it is used for file deliveries that are set up by
672 .forward and filter files. Previously, any settings of the "file" or
673 "directory" options were ignored. It is hoped that, like the address_file
674 transport in the default configuration, these options were never in fact set
675 on such transports, because they were of no use.
676
677 Now, if either of these options is set, it is used. The path that is passed
678 by the router is in $address_file (this is not new), so it can be used as
679 part of a longer path, or modified in any other way that expansion permits.
680
681 If neither "file" nor "directory" is set, the behaviour is unchanged.
682
6834. Related to the above: in a filter, if a "save" command specifies a non-
684 absolute path, the value of $home/ is pre-pended. This no longer happens if
685 $home is unset or is set to an empty string.
686
6875. Multiple file deliveries from a filter or .forward file can never be
688 batched; the value of batch_max on the transport is ignored for file
689 deliveries. I'm assuming that nobody ever actually set batch_max on the
690 address_file transport - it would have had odd effects previously.
691
6926. DESTDIR is the more common variable that ROOT for use when installing
693 software under a different root filing system. The Exim install script now
694 recognizes DESTDIR first; if it is not set, ROOT is used.
695
6967. If DESTDIR is set when installing Exim, it no longer prepends its value to
697 the path of the system aliases file that appears in the default
698 configuration (when a default configuration is installed). If an aliases
699 file is actually created, its name *does* use the prefix.
700
701
702Version 4.14
703------------
704
7051. The default for the maximum number of unknown SMTP commands that Exim will
706accept before dropping a connection has been reduced from 5 to 3. However, you
707can now change the value by setting smtp_max_unknown_commands.
708
7092. The ${quote: operator has been changed so that it turns newline and carriage
710return characters into \n and \r, respectively.
711
7123. The file names used for maildir messages now include the microsecond time
713fraction as well as the time in seconds, to cope with systems where the process
714id can be re-used within the same second. The format is now
715
716 <time>.H<microsec>P<pid>.<host>
717
718This should be a compatible change, but is noted here just in case.
719
7204. The rules for creating message ids have changed, to cope with systems where
721the process id can be re-used within the same second. The format, however, is
722unchanged, so this should not cause any problems, except as noted in the next
723item.
724
7255. The maximum value for localhost_number has been reduced from 255 to 16, in
726order to implement the new message id rules. For operating systems that have
727case-insensitive file systems (Cygwin and Darwin), the limit is 10.
728
7296. verify = header_syntax was allowing unqualified addresses in all cases. Now
730it allows them only for locally generated messages and from hosts that match
731sender_unqualified_hosts or recipient_unqualified_hosts, respectively.
732
7337. For reasons lost in the mists of time, when a pipe transport was run, the
734environment variable MESSAGE_ID was set to the message ID preceded by 'E' (the
735form used in Message-ID: header lines). The 'E' has been removed.
736
737
738Version 4.11
739------------
740
7411. The handling of lines in the configuration file has changed. Previously,
742macro expansion was applied to logical lines, after continuations had been
743joined on. This meant that it could not be used in .include lines, which are
744handled as physical rather than logical lines. Macro expansion is now done on
745physical lines rather than logical lines. This means there are two
746incompatibilities:
747
748 (a) A macro that expands to # to turn a line into a comment now applies only
749 to the physical line where it appears. Previously, it would have caused
750 any following continuations also to be ignored.
751
752 (b) A macro name can no longer be split over the boundary between a line and
753 its continuation. Actually, this is more of a bug fix. :-)
754
7552. The -D command line option must now all be within one command line item.
756This makes it possible to use -D to set a macro to the empty string by commands
757such as
758
759 exim -DABC ...
760 exim -DABC= ...
761
762Previously, these items would have moved on to the next item on the command
763line. To include spaces in a macro definition item, quotes must be used, in
764which case you can also have spaces after -D and surrounding the equals. For
765example:
766
767 exim '-D ABC = something' ...
768
7693. The way that addresses that redirect to themselves are handled has been
770changed, in order to fix an obscure bug. This should not cause any problems
771except in the case of wanting to go back from a 4.11 (or later) release to an
772earlier release. If there are undelivered messages on the spool that contain
773addresses which redirect to themselves, and the redirected addresses have
774already been delivered, you might get a duplicate delivery if you revert to an
775earlier Exim.
776
7774. The default way of looking up IP addresses for hosts in the manualroute and
778queryprogram routers has been changed. If "byname" or "bydns" is explicitly
779specified, there is no change, but if no method is specified, Exim now behaves
780as follows:
781
782 First, a DNS lookup is done. If this yields anything other than
783 HOST_NOT_FOUND, that result is used. Otherwise, Exim goes on to try a call to
784 getipnodebyname() (or gethostbyname() on older systems) and the result of the
785 lookup is the result of that call.
786
787This change has been made because it has been discovered that on some systems,
788if a DNS lookup called via getipnodebyname() times out, HOST_NOT_FOUND is
789returned instead of TRY_AGAIN. Thus, it is safest to try a DNS lookup directly
790first, and only if that gives a definite "no such host" to try the local
791function.
792
7935. In fixing the minor security problem with pid_file_path, I have removed some
794backwards-compatible (undocumented) code which was present to ease conversion
795from Exim 3. In Exim 4, pid_file_path is a literal; in Exim 3 it was allowed to
796contain "%s", which was replaced by the port number for daemons listening on
797non-standard ports. In Exim 4, such daemons do not write a pid file. The
798backwards compatibility feature was to replace "%s" by nothing if it occurred
799in an Exim 4 setting of pid_file_path. The bug was in this code. I have solved
800the problem by removing the backwards compatibility feature. Thus, if you still
801have "%s" somewhere in a setting of pid_file_path, you should remove it.
802
8036. There has been an extension to lsearch files. The keys in these files may
804now be quoted in order to allow for whitespace and colons in them. This means
805that if you were previously using keys that began with a doublequote, you will
806now have to wrap them with extra quotes and escape the internal quotes. The
807possibility that anybody is actually doing this seems extremely remote, but it
808is documented just in case.
809
810
811Version 4.10
812------------
813
814The build-time parameter EXIWHAT_KILL_ARG has been renamed EXIWHAT_KILL_SIGNAL
815to better reflect its function. The OS-specific files have been updated. Only
816if you have explicitly set this in your Makefile (highly unlikely) do you need
817to change anything.
818
819****