SPAMD/malware: Log service identity with errors. Bug 1740

[exim.git] / src / src / configure.default

diff --git a/src/src/configure.default b/src/src/configure.default
index 12743499cf2f6247e5760060d6a444425ded8923..ec60700dfefbef91b2d97dd8d285e26f006e5cbb 100644 (file)
--- a/src/src/configure.default
+++ b/src/src/configure.default
@@ -221,18 +221,26 @@ never_users = root
 host_lookup = *
 
 
-# The settings below, which are actually the same as the defaults in the
-# code, cause Exim to make RFC 1413 (ident) callbacks for all incoming SMTP
-# calls. You can limit the hosts to which these calls are made, and/or change
-# the timeout that is used. If you set the timeout to zero, all RFC 1413 calls
-# are disabled. RFC 1413 calls are cheap and can provide useful information
-# for tracing problem messages, but some hosts and firewalls have problems
-# with them. This can result in a timeout instead of an immediate refused
-# connection, leading to delays on starting up SMTP sessions. (The default was
-# reduced from 30s to 5s for release 4.61.)
+# The settings below cause Exim to make RFC 1413 (ident) callbacks
+# for all incoming SMTP calls. You can limit the hosts to which these
+# calls are made, and/or change the timeout that is used. If you set
+# the timeout to zero, all RFC 1413 calls are disabled. RFC 1413 calls
+# are cheap and can provide useful information for tracing problem
+# messages, but some hosts and firewalls have problems with them.
+# This can result in a timeout instead of an immediate refused
+# connection, leading to delays on starting up SMTP sessions.
+# (The default was reduced from 30s to 5s for release 4.61. and to
+# disabled for release 4.86)
+#
+#rfc1413_hosts = *
+#rfc1413_query_timeout = 5s
+
 
-rfc1413_hosts = *
-rfc1413_query_timeout = 5s
+# Enable an efficiency feature.  We advertise the feature; clients
+# may request to use it.  For multi-recipient mails we then can
+# reject or accept per-user after the message is received.
+#
+prdr_enable = true
 
 
 # By default, Exim expects all envelope addresses to be fully qualified, that
@@ -248,6 +256,13 @@ rfc1413_query_timeout = 5s
 # and/or qualify_recipient (see above).
 
 
+# Unless you run a high-volume site you probably want more logging
+# detail than the default.  Adjust to suit.
+
+log_selector = +smtp_protocol_error +smtp_syntax_error \
+       +tls_certificate_verified
+
+
 # If you want Exim to support the "percent hack" for certain domains,
 # uncomment the following line and provide a list of domains. The "percent
 # hack" is the feature by which mail addressed to x%y@z (where z is one of
@@ -477,6 +492,11 @@ acl_check_rcpt:
 
 acl_check_data:
 
+  # Deny if the message contains an overlong line.  Per the standards
+  # we should never receive one such via SMTP.
+  #
+  deny    condition  = ${if > {$max_received_linelength}{998}}
+
   # Deny if the message contains a virus. Before enabling this check, you
   # must install a virus scanner and set the av_scanner option above.
   #
@@ -669,9 +689,13 @@ begin transports
 
 
 # This transport is used for delivering messages over SMTP connections.
+# Refuse to send any messsage with over-long lines, which could have
+# been receved other than via SMTP. The use of message_size_limit to
+# enforce this is a red herring.
 
 remote_smtp:
   driver = smtp
+  message_size_limit = ${if > {$max_received_linelength}{998} {1}{0}}
 
 
 # This transport is used for local delivery to user mailboxes in traditional